ROOM TEMPERATURE SENSOR INSTALLATION


  1. INSTALL ROOM TEMPERATURE SENSOR


    1. A01JA7X

      Engage the 2 claws to install the room temperature sensor to the No. 1 switch hole base.

  2. INSTALL NO. 1 SWITCH HOLE BASE


    1. Connect the connector.

    2. A01J8XE

      Engage the 5 claws to install the No. 1 switch hole base.

  3. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. A01JAX3

      Temporarily install the console box assembly.

    2. A01J96G

      Engage the 9 claws as shown in the illustration.

    3. A01J9NZ

      Install the to install the upper instrument panel finish panel assembly with the 2 bolts <A>.

    4. Engage the clamp.

  4. INSTALL SHIFT LOCK CONTROL UNIT ASSEMBLY


    1. A01JBN7

      Install the shift lock control unit assembly with the 3 nuts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

    2. Connect the connector to the shift lock control unit assembly.

  5. INSTALL AIR CONDITIONING CONTROL ASSEMBLY


    1. Connect the connector.

      Note

      Since the connectors for the air conditioning control assembly and the integration control and panel sub-assembly are the same shape, take care to connect each connector to the correct component.

    2. A01JAF5

      Engage the 4 claws to install the air conditioning control assembly.

  6. INSTALL CONSOLE BOX ASSEMBLY


    1. Connect each connector.

    2. A01JAOG

      Engage the 4 guides and 2 claws as shown in the illustration.

    3. A01J9IU

      Install the console box assembly with the bolt <B> and 2 clips.

  7. INSTALL BOX BOTTOM MAT


    1. A01JACR

      Engage the fastener to install the box bottom mat.

  8. INSTALL FRONT NO. 2 CONSOLE BOX INSERT


    1. A01JAEDE01

      Engage the guide and 4 claws to install the front No. 2 console box insert as shown in the illustration.

  9. INSTALL FRONT NO. 1 CONSOLE BOX INSERT


    1. A01J9VEE01

      Engage the guide and 4 claws to install the front No. 1 console box insert as shown in the illustration.

  10. INSTALL NO. 2 CONSOLE BOX MOUNTING BRACKET


    1. A01J8ZI

      Install the No. 2 console box mounting bracket with the 6 bolts <B>.

  11. INSTALL ELECTRICAL KEY OSCILLATOR


    1. A01J8YH

      Engage the clamp and install the electrical key oscillator.

      Note

      Be careful when installing the electrical key oscillator. If the oscillator is dropped, replace it with a new one.

    2. Connect the connector.

  12. INSTALL REAR CONSOLE BOX ASSEMBLY


    1. Connect the connector.

    2. A01JD37

      Engage the 8 claws as shown in the illustration.

    3. A01JC91

      Install the rear console box assembly with the 5 bolts.

  13. INSTALL CONSOLE BOX CARPET


    1. A01JBT3

      Install the console box carpet.

  14. INSTALL UPPER CONSOLE PANEL


    1. A01J9D7

      Engage the 3 claws to install the upper console panel.

  15. INSTALL REAR CONSOLE BOX POCKET


    1. A01JD2L

      Install the rear console box pocket as shown in the illustration.

  16. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. A01JD4M

      Connect the connector.

    2. Engage the 3 claws to install the upper instrument panel finish panel sub-assembly.

  17. INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Connect the connector.

    2. Engage the 14 claws to install the instrument cluster finish panel garnish.

      A01J8FE

  18. INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. A01J96O

      Engage the 7 claws and 2 clips to install the lower center instrument cluster finish panel sub-assembly.

  19. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY


    1. A01JCDA

      Connect each connector.

    2. Engage the 6 claws to install the integration control and panel assembly.

  20. INSPECT SHIFT LEVER


    1. Turn the power switch on (READY).

    2. Check that all available shift positions can be selected moving the shift lever.

      Tech Tips

      After the shift lever is replaced with a new one, perform the above operation. If this operation is not performed, moving the shift lever may not initially select shift positions.