REAR SEAT OUTER BELT ASSEMBLY INSTALLATION


  1. INSTALL REAR SEAT OUTER BELT ASSEMBLY


    1. A01J8WC

      Install the ELR anchor bracket with the 2 bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    2. A01JBBX

      Engage the guide and install the rear seat outer belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    3. Check if the ELR locks.

      Note

      The check should be performed with the outer belt assembly installed.


      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

    4. A01JD3CE01
      Text in Illustration
      *1 Protruding Part

      Connect the floor anchor end of the rear seat outer belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding part of the floor panel.

  2. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH (for LH Side)


    1. Engage the 9 clips to install the roof side inner garnish assembly LH.

      A01JCXV

  3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)


    1. Connect the connector.

    2. Engage the 7 claws and 2 clips.

    3. Install the deck trim side panel assembly LH with the screw.

      A01J8UZ

  4. INSTALL TONNEAU COVER HOLDER CAP (for LH Side)


    1. A01JASW

      Engage the claw to install the tonneau cover holder cap.

  5. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)


    1. A01JAKN

      Engage the 2 guides.

    2. Install the 2 luggage hold belt striker assemblies with the 2 bolts.

  6. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH (for RH Side)

    Tech Tips

    Use the same procedure described for the LH side.

  7. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)


    1. Engage the 7 claws and 2 clips.

    2. Install the deck trim side panel assembly RH with the screw.

      A01JCY2

  8. INSTALL TONNEAU COVER HOLDER CAP (for RH Side)

    Tech Tips

    Use the same procedure described for the LH side.

  9. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure described for the LH side.

  10. INSTALL REAR SIDE SEATBACK ASSEMBLY LH (for LH Side)


    1. A01JABT

      Engage the 2 guides as shown in the illustration.

    2. A01J9D6

      Install the rear side seatback assembly LH with the bolt.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  11. INSTALL REAR SIDE SEATBACK ASSEMBLY RH (for RH Side)

  12. INSTALL REAR SEAT CUSHION ASSEMBLY

  13. INSTALL REAR DECK TRIM COVER


    1. A01JCDX

      Engage the 4 claws and 4 guides to install the rear deck trim cover.

  14. INSTALL DECK TRIM SERVICE HOLE COVER


    1. A01JD05

      Engage the 3 guides.

    2. Engage the 2 claws to install the deck trim service hole cover.

  15. INSTALL REAR NO. 1 FLOOR BOARD


    1. A01JBVX

      Engage the 2 claws and 2 clips.

    2. Install the rear No. 1 floor board with the bolt.

  16. INSTALL REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY


    1. A01JCFP

      Engage the claw and 2 clips to install the rear No. 2 floor board sub-assembly.

  17. INSTALL REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY


    1. A01J8Q1

      Engage the 2 claws and 2 clips to install the rear No. 1 floor board sub-assembly.

  18. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Install the tonneau cover assembly.

  19. INSTALL DECK FLOOR BOX LH (for LH Side)


    1. A01J9G6

      Engage the 2 guides.

    2. Install the deck floor box LH with the clip.

  20. INSTALL REAR NO. 4 FLOOR BOARD (for LH Side)


    1. A01JB13

      Engage the guide to install the rear No. 4 floor board.

  21. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP


    1. A01JBZWE01
      Text in Illustration
      *1 Alignment Mark (Red)

      Align the alignment mark (Red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  22. INSTALL REAR DOOR SCUFF PLATE


    1. A01JA7L

      Engage the 7 claws to install the rear door scuff plate LH.

  23. INSTALL REAR NO. 3 FLOOR BOARD (for RH Side)


    1. A01JC33

      Engage the 2 guides to install the rear No. 3 floor board.

  24. INSTALL REAR DECK FLOOR BOX


    1. Install the rear deck floor box.

  25. INSTALL REAR NO. 2 FLOOR BOARD


    1. A01JCWRE01

      Engage the 3 guides <A>.

    2. Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.