FRONT SEAT OUTER BELT ASSEMBLY INSTALLATION


  1. INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY


    1. A01J955E01

      Engage the guide to temporarily install the front shoulder belt anchor adjuster assembly with the 2 bolts.

    2. Fully tighten the bolt <A> first, then the bolt <B> to install the front shoulder belt anchor adjuster assembly.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  2. INSTALL FRONT SEAT OUTER BELT ASSEMBLY


    1. A01JBT1E01

      Temporarily install the front seat outer belt assembly with the 2 bolts.

    2. Fully tighten the bolt <A> first, then the bolt <B> to install the front seat outer belt assembly.

      Torque:
      Bolt <A>
      7.5 N*m  { 77 kgf*cm, 66 in.*lbf }
      Bolt <B>
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    3. A01JCSR

      Connect the connector and lock the locking button as shown in the illustration.

      Note

      Securely lock the locking button.

    4. Connect each connector.

    5. A01JD1D

      Connect the shoulder anchor of the front seat outer belt assembly with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  3. INSTALL CENTER PILLAR GARNISH


    1. Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar garnish LH.

    2. A01J9M7

      Engage the clip.

    3. Install the center pillar garnish LH with the screw.

  4. INSTALL CENTER PILLAR LOWER GARNISH


    1. A01JAI1

      Engage the 2 claws and 2 clips to install the center pillar lower garnish LH.

  5. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01JBZWE01
      Text in Illustration
      *1 Alignment Mark (Red)

      Align the alignment mark (Red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  6. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01JBZWE01
      Text in Illustration
      *1 Alignment Mark (Red)

      Align the alignment mark (Red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  7. CONNECT FRONT SEAT OUTER BELT ASSEMBLY


    1. A01J9GA

      Install the floor end of the front seat outer belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    2. Check if the ELR locks.

      Note

      The check should be performed with the outer belt assembly installed.


      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

  8. INSTALL LAP BELT OUTER ANCHOR COVER


    1. A01JB4X

      Engage the 3 claws to install the lap belt outer anchor cover.

  9. INSTALL REAR DOOR SCUFF PLATE


    1. A01JA7L

      Engage the 7 claws to install the rear door scuff plate LH.

  10. INSTALL FRONT DOOR SCUFF PLATE


    1. A01JB0N

      Engage the 10 claws to install the front door scuff plate LH.

  11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  12. INSTALL REAR NO. 3 FLOOR BOARD


    1. A01JC33

      Engage the 2 guides to install the rear No. 3 floor board.

  13. INSTALL REAR DECK FLOOR BOX


    1. Install the rear deck floor box.

  14. INSTALL REAR NO. 2 FLOOR BOARD


    1. A01JCWRE01

      Engage the 3 guides <A>.

    2. Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.

  15. INSPECT SRS WARNING LIGHT


    1. Inspect the SRS warning light Click here.