FRONT SEAT CUSHION HEATER (for Manual Seat) REMOVAL


  1. PRECAUTION (w/ Navigation System for HDD)

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

  2. REMOVE REAR NO. 2 FLOOR BOARD


    1. A01JB5ZE01

      Disengage the 2 guides <A> as shown in the illustration.

    2. Disengage the 3 guides <B> and remove the rear No. 2 floor board.

  3. REMOVE REAR DECK FLOOR BOX


    1. Remove the rear deck floor box.

  4. REMOVE REAR NO. 3 FLOOR BOARD


    1. A01JC33

      Disengage the 2 guides and remove the rear No. 3 floor board.

  5. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  6. REMOVE FRONT SEAT HEADREST ASSEMBLY


    1. A01JBSO

      Press the headrest support button and pull up the headrest as shown in the illustration to remove it.

  7. REMOVE OUTER SEAT TRACK COVER


    1. A01J9SP

      Lift up the seat track adjusting handle and move the seat to the foremost position.

    2. Disengage the 2 claws and remove the outer seat track cover.

  8. REMOVE INNER SEAT TRACK COVER


    1. Disengage the claw.

    2. A01JBVL

      Separate the guide and remove the inner seat track cover.

  9. REMOVE FRONT SEAT ASSEMBLY


    1. A01J916

      Remove the 2 bolts on the rear side of the seat.

    2. Lift up the seat track adjusting handle and move the seat to the rearmost position.

    3. A01JATS

      Remove the 2 bolts on the front side of the seat.

    4. Lift up the seat track adjusting handle and move the seat to the center position. Also, operate the reclining adjuster release handle and move the seatback to the upright position.

    5. Disconnect the connectors under the seat.

    6. Remove the seat.

      Note

      Be careful not to damage the vehicle body.

  10. REMOVE RECLINING ADJUSTER RELEASE HANDLE


    1. A01J8SME01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver wrapped with protective tape, disengage the claw and remove the reclining adjuster release handle.

  11. REMOVE VERTICAL ADJUSTING HANDLE


    1. A01J9YL

      Remove the screw and vertical adjusting handle.

  12. REMOVE FRONT SEAT CUSHION SHIELD ASSEMBLY


    1. A01JCR1

      Remove the screw.

    2. Disengage the 2 claws and clip.

    3. w/ Lumbar Support:


      1. A01JAOR

        Disconnect the connector.

      2. Disengage the 5 clamps and remove the front seat cushion shield assembly.

  13. REMOVE FRONT SEAT INNER BELT ASSEMBLY


    1. Disconnect each connector.

    2. Disengage each clamp.

    3. A01J9T3

      Remove the nut and front seat inner belt assembly.

  14. REMOVE FRONT SEAT CUSHION INNER SHIELD


    1. A01JAD7

      Disengage the 2 claws and remove the front seat cushion inner shield.

  15. REMOVE FRONT SEAT CUSHION COVER WITH PAD


    1. A01JAJH

      Remove the hook.

    2. w/ Lumbar Support:


      1. A01JCQZ

        Disconnect the connector.

      2. Disengage the 3 clamps.

      3. A01JAZP

        Disengage the 4 clamps.

    3. w/ Seat Heater System:


      1. A01JAAJ

        Disconnect the connector.

      2. Unfasten the front seat cushion cover with pad as shown in the illustration.

      3. A01JCCI

        Disengage the clamp.

    4. A01J9KL

      Disengage the 4 hooks.

    5. for Passenger Side:


      1. A01JDA4

        Disconnect the connector.

      2. Disengage the 3 clamps.

      3. A01JBF5

        Disengage the guide and remove the belt warning occupant detection sensor.

    6. A01JA3G

      Remove the 3 hog rings.

    7. A01J8XV

      Disengage the 2 hooks as shown in the illustration.

    8. Disengage each hook and remove the front seat cushion cover with pad as shown in the illustration.

      A01JAUZ

  16. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. A01JD7U

      Remove the 2 hog rings.

    2. A01J8MM

      Remove the 11 hog rings and the separate type front seat cushion cover.