AIRBAG CUT-OFF INDICATOR LIGHT INSTALLATION


  1. INSTALL PASSENGER SEAT BELT WARNING LIGHT ASSEMBLY


    1. A01J98H

      Engage the 2 claws to install the passenger seat belt warning light assembly.

  2. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Connect the connector.

    2. Engage the 7 claws.

    3. Install the center instrument cluster finish panel garnish with the 2 screws <C>.

  3. INSTALL GLOVE COMPARTMENT DOOR


    1. Open the glove compartment door assembly.

    2. A01J9YD

      Insert the glove compartment door as shown in the illustration.

    3. Engage the 7 claws to install the glove compartment door.

  4. INSTALL NO. 2 INSTRUMENT PANEL REGISTER


    1. A01JA22

      Engage the 3 claws and clip to install the No. 2 instrument panel register.

  5. INSTALL NO. 1 SIDE DEFROSTER NOZZLE


    1. A01JAQW

      Engage the 3 claws to install the No. 1 side defroster nozzle.

  6. INSTALL RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)


    1. A01JBMF

      Install the radio tuner opening cover with bracket with the 4 bolts <B>.

  7. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Radio Receiver)


    1. A01JADX

      Engage the 4 claws to install the center instrument cluster finish panel sub-assembly.

  8. INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type)


    1. Connect each connector.

    2. Engage the 4 claws.

    3. Install the radio and display receiver assembly with bracket with the 4 bolts.

  9. INSTALL NAVIGATION RECEIVER WITH BRACKET (for Navigation Receiver Type)


    1. A01JAM5

      Engage the 4 claws and temporarily install the navigation receiver with bracket as shown in the illustration.

    2. Install the navigation receiver with bracket with the 4 bolts.

  10. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. A01JD4M

      Connect the connector.

    2. Engage the 3 claws to install the upper instrument panel finish panel sub-assembly.

  11. INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Connect the connector.

    2. Engage the 14 claws to install the instrument cluster finish panel garnish.

  12. INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. A01J96O

      Engage the 7 claws and 2 clips to install the lower center instrument cluster finish panel sub-assembly.

  13. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY


    1. A01JCDA

      Connect each connector.

    2. Engage the 6 claws to install the integration control and panel assembly.

  14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  15. INSTALL REAR NO. 3 FLOOR BOARD


    1. A01JC33

      Engage the 2 guides to install the rear No. 3 floor board.

  16. INSTALL REAR DECK FLOOR BOX


    1. Install the rear deck floor box.

  17. INSTALL REAR NO. 2 FLOOR BOARD


    1. A01JCWRE01

      Engage the 3 guides <A>.

    2. Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.

  18. PERFORM DIAGNOSTIC SYSTEM CHECK


    1. Perform a diagnostic system check Click here.

  19. INSPECT SRS WARNING LIGHT


    1. Inspect the SRS warning light Click here.