AIRBAG CUT-OFF INDICATOR LIGHT REMOVAL


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing Click here.

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. REMOVE REAR NO. 2 FLOOR BOARD


    1. A01JB5ZE01

      Disengage the 2 guides <A> as shown in the illustration.

    2. Disengage the 3 guides <B> and remove the rear No. 2 floor board.

  3. REMOVE REAR DECK FLOOR BOX


    1. Remove the rear deck floor box.

  4. REMOVE REAR NO. 3 FLOOR BOARD


    1. A01JC33

      Disengage the 2 guides and remove the rear No. 3 floor board.

  5. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  6. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY


    1. A01J9ZGE01
      Text in Illustration
      *a Lift slightly

      Using a moulding remover, slightly lift the panel at the position shown in the illustration.

    2. Pull the integration control and panel assembly in the direction indicated by the arrow to disengage the 6 claws.

    3. Disconnect each connector and remove the integration control and panel assembly.

  7. REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. A01JA02

      Pull the lower center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 2 claws and 2 clips.

    2. A01JAMJ

      Pull the lower center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 5 claws and remove the lower center instrument cluster finish panel sub-assembly.

  8. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Disengage the 14 claws.

    2. Disconnect the connector and remove the instrument cluster finish panel garnish.

      A01J8FE

  9. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. A01JD4M

      Disengage the 3 claws.

    2. Disconnect the connector and remove the upper instrument panel finish panel sub-assembly.

  10. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Radio Receiver)


    1. A01JADX

      Disengage the 4 claws and remove the center instrument cluster finish panel sub-assembly.

  11. REMOVE RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)


    1. A01JBMF

      Remove the 4 bolts <B> and radio tuner opening cover with bracket.

  12. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type)


    1. A01JA1Y

      Remove the 4 bolts.

    2. A01JBHB

      Disengage the 4 claws as shown in the illustration.

    3. Disconnect each connector and remove the radio and display receiver assembly with bracket.

  13. REMOVE NAVIGATION RECEIVER WITH BRACKET (for Navigation Receiver Type)


    1. A01JCMN

      Remove the 4 bolts.

    2. A01J9QE

      Disengage the 4 claws and remove the navigation receiver with bracket as shown in the illustration.

    3. Disconnect each connector.

  14. REMOVE NO. 1 SIDE DEFROSTER NOZZLE


    1. A01JCQ6E01
      Text in Illustration
      *a Lift slightly

      Using a moulding remover, slightly lift the panel at the position shown in the illustration.

    2. Pull the No. 1 side defroster nozzle in the direction indicated by the arrow to disengage the 3 claws and remove the No. 1 side defroster nozzle.

  15. REMOVE NO. 2 INSTRUMENT PANEL REGISTER


    1. A01JBR5

      Pull the No. 2 instrument panel register in the direction indicated by the arrow to disengage the claw and clip.

    2. A01JAS9

      Pull the No. 2 instrument panel register in the direction indicated by the arrow to disengage the 2 claws and remove the No. 2 instrument panel register.

  16. REMOVE GLOVE COMPARTMENT DOOR


    1. Open the glove compartment door assembly.

    2. A01JD7O

      Pull the glove compartment door in the direction indicated by the arrow to disengage the 7 claws.

    3. Pull the glove compartment door in the direction indicated by the arrow to remove the glove compartment door.

  17. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Remove the 2 screws <C>.

    2. Disengage the 7 claws.

    3. Disconnect the connector and remove the center instrument cluster finish panel garnish.

      A01JB9T

  18. REMOVE PASSENGER SEAT BELT WARNING LIGHT ASSEMBLY


    1. A01J98H

      Disengage the 2 claws to remove the passenger seat belt warning light assembly.