REAR AIRBAG SENSOR INSTALLATION

Tech Tips

Use the same procedure for the RH side and LH side.
The procedure listed below is for the LH side.

INSTALL REAR AIRBAG SENSOR
1. Check that the power switch is off.
2. Check that the cable is disconnected from the negative (-) battery terminal.
  
  CAUTION:
  
  Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
3. Insert the pin (stopper) into the body hole to install the rear airbag sensor to the vehicle with the nut.
  
  Torque:
  
  9.0 N*m { 92 kgf*cm, 80 in.*lbf }
  Note
  
  If the rear airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
  
  When installing the rear airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.
  
  Make sure that the pin (stopper) is securely inserted into the body hole.
  
  Tighten the nut while holding the rear airbag sensor because the rear airbag sensor pin (stopper) is easily damaged.
4. Connect the connector to the rear airbag sensor.
  
  Note
  
  When connecting any airbag connector, take care not to damage the airbag wire harness.
  1. Connect the connector as shown in the illustration (when locking, make sure that the outer connector locking sleeve returns to its original position and a click sound can be heard).
    
    Text in Illustration
    
    *1 Outer Connector Locking Sleeve - -
    
    Tech Tips
    
    When connected, the outer connector locking sleeve will slide. Be sure not to hold the outer connector locking sleeve while connecting, as it may result in an insecure fit.
5. Check that there is no looseness in the installation parts of the rear airbag sensor.
INSTALL NO. 1 HYBRID BATTERY INTAKE DUCT (for RH Side)
Note

Ensure that the duct is installed securely.
1. Install the No. 1 hybrid battery intake duct with the 2 clips.
INSTALL REAR FLOOR BOARD SPACER (for RH Side)
1. Install the rear floor board spacer with the 2 clips.
INSTALL REAR NO. 1 FLOOR BOARD (for RH Side)
1. Engage the 2 claws and 2 clips.
2. Install the rear No. 1 floor board with the bolt.
INSTALL REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY (for RH Side)
1. Engage the claw and 2 clips to install the rear No. 2 floor board sub-assembly.
INSTALL REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY (for RH Side)
1. Engage the 2 claws and 2 clips to install the rear No. 1 floor board sub-assembly.
INSTALL REAR SIDE SEATBACK ASSEMBLY

for LH Side: Click here

for RH Side: Click here
INSTALL REAR DOOR SCUFF PLATE
1. Engage the 7 claws to install the rear door scuff plate LH.

Text in Illustration
*1	Outer Connector Locking Sleeve	-	-

INSTALL REAR SEAT CUSHION ASSEMBLY

Text in Illustration
*1	100 mm (3.94 in.) or less
*2	Guide
*3	Hook

Engage the 2 guides of the seat cushion to the seatback.

Engage the 2 front hooks of the seat cushion to the vehicle body.

Note

When installing the seat cushion, make sure that the seat belt buckle is not under the seat cushion.

Tech Tips

Confirm that the seat cushion is firmly installed.

CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
INSTALL REAR NO. 3 FLOOR BOARD
1. Engage the 2 guides to install the rear No. 3 floor board.
INSTALL REAR DECK FLOOR BOX
1. Install the rear deck floor box.
INSTALL REAR NO. 2 FLOOR BOARD
1. Engage the 3 guides <A>.
2. Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.
PERFORM DIAGNOSTIC SYSTEM CHECK
1. Perform a diagnostic system check Click here.
INSPECT SRS WARNING LIGHT
1. Inspect the SRS warning light Click here.