CENTER AIRBAG SENSOR ASSEMBLY REMOVAL


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing Click here.

    Note

    w/ Navigation System for HDD:

    After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.

  2. REMOVE REAR NO. 2 FLOOR BOARD


    1. A01JB5ZE01

      Disengage the 2 guides <A> as shown in the illustration.

    2. Disengage the 3 guides <B> and remove the rear No. 2 floor board.

  3. REMOVE REAR DECK FLOOR BOX


    1. Remove the rear deck floor box.

  4. REMOVE REAR NO. 3 FLOOR BOARD


    1. A01JC33

      Disengage the 2 guides and remove the rear No. 3 floor board.

  5. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  6. REMOVE REAR CONSOLE BOX ASSEMBLY

    Tech Tips

    Refer to the procedure up to Remove Rear Console Box Assembly Click here.

  7. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY


    1. A01J9ZGE01
      Text in Illustration
      *a Lift slightly

      Using a moulding remover, slightly lift the panel at the position shown in the illustration.

    2. Pull the integration control and panel assembly in the direction indicated by the arrow to disengage the 6 claws.

    3. Disconnect each connector and remove the integration control and panel assembly.

  8. REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. A01JA02

      Pull the lower center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 2 claws and 2 clips.

    2. A01JAMJ

      Pull the lower center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 5 claws and remove the lower center instrument cluster finish panel sub-assembly.

  9. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Disengage the 14 claws.

    2. Disconnect the connector and remove the instrument cluster finish panel garnish.

      A01J8FE

  10. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. A01JD4M

      Disengage the 3 claws.

    2. Disconnect the connector and remove the upper instrument panel finish panel sub-assembly.

  11. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Radio Receiver)


    1. A01JADX

      Disengage the 4 claws and remove the center instrument cluster finish panel sub-assembly.

  12. REMOVE RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)


    1. A01JBMF

      Remove the 4 bolts <B> and radio tuner opening cover with bracket.

  13. REMOVE RADIO RECEIVER WITH BRACKET (w/o Navigation System)


    1. A01JD1M

      Remove the 4 bolts.

    2. A01J8MZ

      Disengage the 4 claws as shown in the illustration.

    3. Disconnect each connector and remove the radio receiver with bracket.

  14. REMOVE NAVIGATION RECEIVER WITH BRACKET (w/ Navigation System)


    1. A01JCMN

      Remove the 4 bolts.

    2. A01J9QE

      Disengage the 4 claws and remove the navigation receiver assembly with bracket as shown in the illustration.

    3. Disconnect each connector.

  15. REMOVE NO. 1 SIDE DEFROSTER NOZZLE


    1. A01JCQ6E01
      Text in Illustration
      *a Lift slightly

      Using a moulding remover, slightly lift the panel at the position shown in the illustration.

    2. Pull the No. 1 side defroster nozzle in the direction indicated by the arrow to disengage the 3 claws and remove the No. 1 side defroster nozzle.

  16. REMOVE NO. 2 INSTRUMENT PANEL REGISTER


    1. A01JBR5

      Pull the No. 2 instrument panel register in the direction indicated by the arrow to disengage the claw and clip.

    2. A01JAS9

      Pull the No. 2 instrument panel register in the direction indicated by the arrow to disengage the 2 claws and remove the No. 2 instrument panel register.

  17. REMOVE GLOVE COMPARTMENT DOOR


    1. Open the glove compartment door assembly.

    2. A01JD7O

      Pull the glove compartment door in the direction indicated by the arrow to disengage the 7 claws.

    3. Pull the glove compartment door in the direction indicated by the arrow to remove the glove compartment door.

  18. REMOVE AIR CONDITIONING CONTROL ASSEMBLY


    1. A01JCGH

      Disengage the 4 claws and remove the air conditioning control assembly as shown in the illustration.

    2. Disconnect the connector.

      Note

      Since the connectors for the air conditioning control assembly and the integration control and panel sub-assembly are the same shape, mark them so that they will not be reconnected incorrectly.

  19. REMOVE SHIFT LOCK CONTROL UNIT ASSEMBLY


    1. A01JBN7

      Disconnect the connector from the shift lock control unit assembly.

    2. Remove the 3 nuts and shift lock control unit assembly.

  20. REMOVE ELECTRICAL KEY OSCILLATOR


    1. A01J8YH

      Disconnect the connector.

    2. Disengage the clamp and remove the electrical key oscillator.

      Note

      Be careful when removing the electrical key oscillator. If the oscillator is dropped, replace it with a new one.

  21. REMOVE NO. 2 CONSOLE BOX MOUNTING BRACKET


    1. A01J8ZI

      Remove the 6 bolts <B> and No. 2 console box mounting bracket.

  22. REMOVE FRONT NO. 1 CONSOLE BOX INSERT


    1. A01JBU8E01

      Pull the front No. 1 console box insert in the direction indicated by the arrow to disengage the 4 claws and guide, and remove the front No. 1 console box insert.

  23. REMOVE FRONT NO. 2 CONSOLE BOX INSERT


    1. A01J9HYE01

      Pull the front No. 2 console box insert in the direction indicated by the arrow to disengage the 4 claws and guide, and remove the front No. 2 console box insert.

  24. REMOVE BOX BOTTOM MAT


    1. A01JACR

      Disengage the fastener and remove the box bottom mat.

  25. SEPARATE CONSOLE BOX ASSEMBLY


    1. A01J9IU

      Remove the bolt <B> and 2 clips.

    2. A01JAI8

      While pushing the parts shown in the illustration inward, pull the console box assembly in the direction indicated by the arrow to disengage the 2 claws and 4 guides.

    3. Disconnect the connector and separate the console box assembly.

  26. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. A01J9NZ

      Disengage the clamp.

    2. Remove the 2 bolts <A>.

    3. A01JCLT

      Pull the upper instrument panel finish panel assembly in the direction indicated by the arrow to disengage the 9 claws and remove the upper instrument panel finish panel assembly.

  27. REMOVE CONSOLE BOX ASSEMBLY


    1. A01JAX3

      Remove the console box assembly.

  28. REMOVE CENTER AIRBAG SENSOR ASSEMBLY


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01JCS1

      Disconnect the connectors from the center airbag sensor assembly as shown in the illustration.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

    4. Remove the 3 bolts and center airbag sensor assembly.