KNEE AIRBAG ASSEMBLY INSTALLATION


  1. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01JBZS

      Connect the airbag connector and install the clamp to the driver side knee airbag assembly.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.

    4. Push in the lock to install the airbag connector.

    5. A01JCSU

      Temporarily install the driver side knee airbag assembly with the 6 claws and 4 guides.

    6. A01J9P2

      Install the driver side knee airbag assembly with the 4 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      Confirm that the driver side knee airbag assembly is installed securely without any excessive gaps and is not protruding outward.

  2. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. Connect each connector.

    2. Engage the clamp.

    3. A01J9TK

      Engage the 2 guides and claw to connect the hood lock control cable.

    4. A01J9Q6

      Engage the 6 claws and clip.

    5. A01JA5Y

      Install the lower instrument panel finish panel assembly with the screw <C>.

  3. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)


    1. Connect each connector.

    2. A01JB1P

      Engage the guide and claw.

    3. Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <D>.

  4. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    1. Connect each connector.

    2. A01JA4G

      Engage the guide and 2 claws.

    3. Install the No. 1 instrument panel under cover sub-assembly with the screw <D>.

  5. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A01J99M

      Engage the 2 clips.

    2. Install the cowl side trim board LH with the clip.

  6. INSTALL FRONT DOOR SCUFF PLATE LH


    1. A01JB0N

      Engage the 10 claws to install the front door scuff plate LH.

  7. INSTALL NO. 1 SWITCH HOLE BASE


    1. Connect the connector.

    2. A01J8XE

      Engage the 5 claws to install the No. 1 switch hole base.

  8. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. A01JAX3

      Temporarily install the console box assembly.

    2. A01J96G

      Engage the 9 claws as shown in the illustration.

    3. A01J9NZ

      Install the to install the upper instrument panel finish panel assembly with the 2 bolts <A>.

    4. Engage the clamp.

  9. INSTALL CONSOLE BOX ASSEMBLY


    1. Connect each connector.

    2. A01JAOG

      Engage the 4 guides and 2 claws as shown in the illustration.

    3. A01J9IU

      Install the console box assembly with the bolt <B> and 2 clips.

  10. INSTALL BOX BOTTOM MAT


    1. A01JACR

      Engage the fastener to install the box bottom mat.

  11. INSTALL FRONT NO. 2 CONSOLE BOX INSERT


    1. A01JAEDE01

      Engage the guide and 4 claws to install the front No. 2 console box insert as shown in the illustration.

  12. INSTALL FRONT NO. 1 CONSOLE BOX INSERT


    1. A01J9VEE01

      Engage the guide and 4 claws to install the front No. 1 console box insert as shown in the illustration.

  13. INSTALL NO. 2 CONSOLE BOX MOUNTING BRACKET


    1. A01J8ZI

      Install the No. 2 console box mounting bracket with the 6 bolts <B>.

  14. INSTALL ELECTRICAL KEY OSCILLATOR


    1. A01J8YH

      Engage the clamp and install the electrical key oscillator.

      Note

      Be careful when installing the electrical key oscillator. If the oscillator is dropped, replace it with a new one.

    2. Connect the connector.

  15. INSTALL SHIFT LOCK CONTROL UNIT ASSEMBLY


    1. A01JBN7

      Install the shift lock control unit assembly with the 3 nuts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

    2. Connect the connector to the shift lock control unit assembly.

  16. INSTALL AIR CONDITIONING CONTROL ASSEMBLY


    1. Connect the connector.

      Note

      Since the connectors for the air conditioning control assembly and the integration control and panel sub-assembly are the same shape, take care to connect each connector to the correct component.

    2. A01JAF5

      Engage the 4 claws to install the air conditioning control assembly.

  17. INSTALL GLOVE COMPARTMENT DOOR


    1. Open the glove compartment door assembly.

    2. A01J9YD

      Insert the glove compartment door as shown in the illustration.

    3. Engage the 7 claws to install the glove compartment door.

  18. INSTALL NO. 2 INSTRUMENT PANEL REGISTER


    1. A01JA22

      Engage the 3 claws and clip to install the No. 2 instrument panel register.

  19. INSTALL NO. 1 SIDE DEFROSTER NOZZLE


    1. A01JAQW

      Engage the 3 claws to install the No. 1 side defroster nozzle.

  20. INSTALL RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)


    1. A01JBMF

      Install the radio tuner opening cover with bracket with the 4 bolts <B>.

  21. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Radio Receiver)


    1. A01JADX

      Engage the 4 claws to install the center instrument cluster finish panel sub-assembly.

  22. INSTALL RADIO RECEIVER WITH BRACKET (w/o Navigation System)


    1. Connect each connector.

    2. A01J9D0

      Engage the 4 claws as shown in the illustration.

    3. A01JD1M

      Install the radio receiver with bracket with the 4 bolts.

  23. INSTALL NAVIGATION RECEIVER WITH BRACKET (w/ Navigation System)


    1. A01JAM5

      Engage the 4 claws to temporarily install the navigation receiver assembly with bracket as shown in the illustration.

    2. A01JCMN

      Install the navigation receiver assembly with bracket with the 4 bolts.

  24. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. A01JD4M

      Connect the connector.

    2. Engage the 3 claws to install the upper instrument panel finish panel sub-assembly.

  25. INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Connect the connector.

    2. Engage the 14 claws to install the instrument cluster finish panel garnish.

      A01J8FE

  26. INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. A01J96O

      Engage the 7 claws and 2 clips to install the lower center instrument cluster finish panel sub-assembly.

  27. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY


    1. A01JCDA

      Connect each connector.

    2. Engage the 6 claws to install the integration control and panel assembly.

  28. INSTALL REAR CONSOLE BOX ASSEMBLY

    Tech Tips

    Refer to the procedure from Install Rear Console Box Assembly Click here.

  29. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  30. INSTALL REAR NO. 3 FLOOR BOARD


    1. A01JC33

      Engage the 2 guides to install the rear No. 3 floor board.

  31. INSTALL REAR DECK FLOOR BOX


    1. Install the rear deck floor box.

  32. INSTALL REAR NO. 2 FLOOR BOARD


    1. A01JCWRE01

      Engage the 3 guides <A>.

    2. Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.

  33. PERFORM DIAGNOSTIC SYSTEM CHECK


    1. Perform a diagnostic system check Click here.

  34. INSPECT SRS WARNING LIGHT


    1. Inspect the SRS warning light Click here.