ENTRY LOCK AND UNLOCK SWITCH INSTALLATION


  1. INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY


    1. A01JAX9

      Insert the front end of the front door outside handle assembly into the front door outside handle frame.

    2. Insert the rear end of the front door outside handle assembly into the front door outside handle frame, then slide the front door outside handle assembly toward the front of the vehicle to install it.

    3. A01JCG9

      Move the lever back in the direction indicated by the arrow in the illustration to lock the door outside handle assembly.

    4. A01JAUR

      Connect the connector.

    5. Engage the 2 claws.

  2. INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)


    1. A01JALV

      Using a T30 "TORX" socket wrench, install the front door outside handle cover with the screw.

      Torque:
      4.0 N*m  { 41 kgf*cm, 35 in.*lbf }
    2. A01J8EH

      Install the hole plug.

  3. INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)


    1. A01JBZ1

      Install the front door outside handle cover with lock cylinder assembly.

      Tech Tips

      Make sure that the front door lock cylinder rod is inserted into the front door lock assembly.

    2. A01JCZ6

      Using a T30 "TORX" socket wrench, install the front door lock cylinder with the screw.

      Torque:
      4.0 N*m  { 41 kgf*cm, 35 in.*lbf }
    3. A01J9Y5

      Install the hole plug.

  4. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    1. A01JB2T

      Install the front door rear lower frame sub-assembly with the bolt as shown in the illustration.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  5. INSTALL FRONT DOOR GLASS RUN


    1. A01JD3R

      Install the front door glass run.

  6. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY


    1. Connect the cable to the negative (-) battery terminal.

    2. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.


      1. w/ Navigation System for HDD:

        Note

        After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.

    3. Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.

    4. A01JAEHE01

      Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows, in the order shown in the illustration.

    5. A01JCLM

      Install the front door glass sub-assembly with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
    6. A01J8J2

      Install the grommet.

    7. Connect the cable to the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  7. INSTALL FRONT DOOR SERVICE HOLE COVER


    1. Apply butyl tape to the front door panel.

    2. A01J8WVE01
      Text in Illustration
      *1 Reference Point

      Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.

    3. Attach the front door service hole cover according to the reference points on the front door panel.

      Note

      Securely install the front door service hole cover preventing wrinkles and air bubbles.

  8. INSTALL FRONT DOOR TRIM BRACKET


    1. A01J9TD

      Install the front door trim bracket with the 2 screws.

  9. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. A01JCTO

      Connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door inside handle.

    2. A01JARO

      Engage the 2 claws and install the front door inside handle sub-assembly to the front door trim board sub-assembly.

  10. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01J8S8

      Engage the 9 clips and install the front door trim board sub-assembly.

    2. Install the 2 screws.

    3. Remove the 2 pieces of protective tape.

  11. INSTALL COURTESY LIGHT ASSEMBLY


    1. Connect the connector.

    2. A01JC7IE01

      Engage the claw to install the courtesy light assembly.

  12. INSTALL DOOR ARMREST COVER


    1. A01JCMQ

      Install the door armrest cover.

  13. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. A01JCY6

      Connect the connector.

    2. Engage the 7 claws and 3 guides, and install the power window regulator master switch assembly with front door armrest base panel.

  14. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    1. Connect the connector.

    2. A01JACF

      Engage the 7 claws and 3 guides, and install the power window regulator switch assembly with front door armrest base panel.

  15. INSTALL ASSIST GRIP COVER


    1. A01JAH9

      Engage the 6 claws, 2 clips and 3 guides, and install the assist grip cover.

  16. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A01JA7Z

      Engage the 3 claws and install the front door inside handle bezel plug.

  17. INSTALL REAR NO. 3 FLOOR BOARD


    1. A01JC33

      Engage the 2 guides to install the rear No. 3 floor board.

  18. INSTALL REAR DECK FLOOR BOX


    1. Install the rear deck floor box.

  19. INSTALL REAR NO. 2 FLOOR BOARD


    1. A01JCWRE01

      Engage the 3 guides <A>.

    2. Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.

  20. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here

  21. CHECK POWER WINDOW CONTROL SYSTEM

    Click here