ENTRY AND START SYSTEM (for Start Function), Diagnostic DTC:B2284

DTC Code DTC Name
B2284 Brake Signal Malfunction

DESCRIPTION

The power management control ECU receives brake signal information from 2 sources. It receives a signal from the stop light switch assembly via a direct line, and a signal from the skid control ECU assembly via CAN. If the information from these 2 sources is inconsistent, this DTC will be stored.

DTC No. DTC Detection Condition Trouble Area
B2284 Stop light switch assembly operation information received by the power management control ECU from the stop light switch assembly via a direct line and stop light switch assembly information from the skid control ECU assembly via CAN are inconsistent.

  • STOP fuse

  • Stop light switch assembly

  • CAN communication system

  • Skid control ECU assembly

  • Power management control ECU

  • Wire harness or connector

WIRING DIAGRAM

A01J8HOE01

INSPECTION PROCEDURE

Note


  • When the power management control ECU is replaced with a new one and the cable from the negative (-) auxiliary battery terminal is connected, the power source mode becomes on (IG) mode. When the auxiliary battery is removed and reinstalled, the power source mode that was selected when the auxiliary battery was removed is restored.

  • Inspect the fuse for circuits related to this system before performing the following inspection procedure.

Tech Tips

Check the connector connection to the terminal to make sure that there is no abnormality such as a loose connection, deformation, etc.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - POWER MANAGEMENT CONTROL ECU)


    1. Disconnect the L5 and L6 connectors from the power management control ECU.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      L5-1 (AM22) - Body ground Always 9.5 to 16 V
      L6-7 (AM21) - Body ground Always 9.5 to 16 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - POWER MANAGEMENT CONTROL ECU)

    OK

  2. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)


    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L5-5 (E01) - Body ground Always Below 1 Ω
      L5-6 (E1) - Body ground Always Below 1 Ω
      L6-4 (E12) - Body ground Always Below 1 Ω
      L6-5 (E02) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)

    OK

  3. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SOURCE AND BODY GROUND)


    1. A01JCQ1E15
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Stop Light Switch Assembly)

      Disconnect the A67 connector from the stop light switch assembly.

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A67-1 (B) - A67-3 (GND) Always 11 to 14 V
      Standard Resistance
      Tester Connection Condition Specified Condition
      A67-3 (GND) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK STOP LIGHT SWITCH ASSEMBLY


    1. A01JCFXE12
      Text in Illustration
      *a

      Component with harness connected

      (Stop Light Switch Assembly)

      Reconnect the A67 connector to the stop light switch assembly.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A67-2 (L) - A67-3 (GND) Power switch off, brake pedal not depressed Below 1 V
      A67-2 (L) - A67-3 (GND) Power switch off, brake pedal depressed 11 to 14 V

    NG

    REPLACE STOP LIGHT SWITCH ASSEMBLY Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER MANAGEMENT CONTROL ECU)


    1. Disconnect the A22 connector from the power management control ECU.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A22-23 (STP) - A67-2 (L) Always Below 1 Ω
      A22-23 (STP) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER MANAGEMENT CONTROL ECU)

    OK

  6. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Power Source Control / Data List.

    5. Read the Data List according to the display on the intelligent tester.

      Power Source Control
      Tester Display Measurement Item/Range Normal Condition Specified Condition
      Stop Light Switch1 Stop light switch1/ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      		 -
      OK
      ON (brake pedal is depressed) and OFF (brake pedal is released) appear on the screen.

    NG

    REPLACE POWER MANAGEMENT CONTROL ECU Click here

    OK

    GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM (DTC C1249/49) Click here