ENTRY AND START SYSTEM (for Start Function) DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Power Source Control / Data List.

    5. Read the Data List according to the display on the intelligent tester.

      Power Source Control
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Stop Light Switch1 Stop light switch 1/ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      		 -
      Start Switch1 Start switch 1/ON or OFF

      ON: Power switch pushed

      OFF: Power switch not pushed

      		 -
      Start Switch2 Start switch 2/ON or OFF

      ON: Power switch pushed

      OFF: Power switch not pushed

      		 -
      Latch Circuit Latch circuit/ON or OFF

      ON: Power switch on (IG) or on (READY)

      OFF: Power switch off or on (ACC)

      		 -
      IG1 Relay Monitor (Outside) IG1 outer relay monitor/ON or OFF

      ON: Power switch on (IG)

      OFF: Power switch off

      		 -
      IG1 Relay Monitor (Inside) IG1 inner relay monitor/ON or OFF

      ON: Power switch on (IG)

      OFF: Power switch off

      		 -
      IG2 Relay Monitor (Outside) IG2 outer relay monitor/ON or OFF

      ON: Power switch on (IG)

      OFF: Power switch off

      		 -
      IG2 Relay Monitor (Inside) IG2 inner relay monitor/ON or OFF

      ON: Power switch on (IG)

      OFF: Power switch off

      		 -
      Starter Request Signal Starter request signal monitor/ON or OFF

      ON: ST relay on

      OFF: ST relay off

      		 -
      ACC Relay Monitor ACC relay monitor/ON or OFF

      ON: Power switch on (ACC)

      OFF: Power switch off

      		 -
      Ready Signal Status of the ready signal/ON or OFF

      ON: Hybrid control system on (on (READY))

      OFF: Hybrid control system off

      		 -
      Vehicle Speed Signal Vehicle speed signal/Stop or Run

      Stop: Vehicle stopped

      Run: Vehicle running

      		 -
      Shift P Signal Pulse Status of the shift P signal pulse/Unknown, Error2, Normal2, Error1, Normal3, Error3 or Normal1

      Unknown: Other

      Error2: Signal abnormal and park (P) selected

      Normal2: Signal normal and park (P) selected

      Error1: Signal abnormal and park (P) state cannot be determined

      Normal3: Signal normal and R, N, D or B selected

      Error3: Signal abnormal and R, N, D or B selected

      Normal1: Signal normal and park (P) state cannot be determined

      		 -
      Power Supply Condition Power supply condition/All OFF, ACC ON, IG1 ON, IG2 ON, ST ON

      All OFF: All relays off

      ACC ON: ACC relay on

      IG1 ON: IG1 relay on

      IG2 ON: IG2 relay on

      ST ON: ST request signal on

      		 -
      Powertrain Type Status of the powertrain type/HV-AT, Conventional-AT, Conventional-MT, Conventional-MMT HV-AT -
      IG1 Circuit Status of the IG1 relay activation circuit/OK or NG

      OK: IG1 relay activation circuit normal

      NG: IG1 relay activation circuit abnormal

      		 -
      IG2 Circuit Status of the IG2 relay activation circuit/OK or NG

      OK: IG2 relay activation circuit normal

      NG: IG2 relay activation circuit abnormal

      		 -
      Starter Switch Signal Mismatch Power switch error detection/No or Yes

      No: Power switch error not detected

      Yes: Power switch error detected

      		 -
      Park Signal Mismatch Status of the park signal mismatch/No or Yes

      No: Park signal mismatch no detected

      Yes: Park signal mismatch detected

      		 -
      Key Certification Waiting Timed Out Key certification error detection/No or Yes

      No: Key certification error not detected

      Yes: Key certification error detected

      		 -
      Number of Diagnosis Code Number of diagnosis code/Min.: 0, MAX.: 255 Number of DTCs will be displayed -

    6. Enter the following menus: Body / Entry & Start / Data List.

    7. Read the Data List according to the display on the intelligent tester.

      Entry & Start
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Ignition Switch Power switch/ON or OFF

      ON: Power switch on (IG)

      OFF: Power switch off

      		 -
      Key Low Battery Low key battery/Yes or No

      Yes: Key battery voltage low

      No: Key battery voltage normal

      		 -
      # Code Number of DTC recorded/Min.: 0, Max.: 225 Number of DTCs displayed -
      Steering Lock Sleep Cond Transmission control ECU sleep condition/Yes or No

      Yes: Transmission control ECU sleep mode can be entered

      No: Transmission control ECU sleep mode cannot be entered

      		 -
      Steering Lock Start Cond Transmission control ECU start signal/Yes or No

      Yes: Transmission control ECU sent a start signal

      No: Transmission control ECU did not send a start signal

      		 -
      Engine Start Condition Hybrid control system start condition/OK or NG

      OK: Hybrid control system allowed to start

      NG: Hybrid control system not allowed to start

      		 -
      Engine Start Request Start request condition signal/OK or NG

      OK: Start request condition signal received

      NG: Start request condition signal not received

      		 -
      3bit Code Request Status of the 3-bit code request/OK or NG

      OK: 3-bit code request signal received

      NG: 3-bit code request signal not received

      		 -
      S Code Check S code certification result/OK or NG

      OK: Certification confirmed

      NG: Certification not confirmed

      		 -
      L Code Check L code certification result/OK or NG

      OK: Certification confirmed

      NG: Certification not confirmed

      		 -
      Unlock Request Receive Status of the gearshift control unlock request receive/OK or NG

      OK: Gearshift control unlock request signal received

      NG: Gearshift control unlock request signal not received

      		 -
      Lock Request Receive Status of the gearshift control lock request receive/OK or NG

      OK: Gearshift control lock request signal received

      NG: Gearshift control lock request signal not received

      		 -
      S Code Check (Past) S code certification result (Past)/OK or NG

      OK: Certification confirmed (past)

      NG: Certification not confirmed (past)

      		 -
      L Code Check (Past) L code verification result (Past)/OK or NG

      OK: Certification confirmed (past)

      NG: Certification not confirmed (past)

      		 -
      EFI Code Receive SFI communication (when DTC stored)/OK or NG

      OK: SFI code received

      NG: SFI code not received

      		 -
      EFI Communication SFI communication /OK or NG

      OK: SFI communication normal

      NG: SFI communication abnormal

      		 -
      Ignition Available Area Ignition available area/Front or All Customization status displayed -

  2. ACTIVE TEST

    Tech Tips

    Using the intelligent tester to perform Active Tests allows relay, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Power Source Control / Active Test.

    5. Perform the Active Test according to the display on the intelligent tester.

      Power Source Control
      Tester Display Test Part Control Range Diagnostic Note
      Indicator Condition Power switch indicator Green/Red/No Sig Power switch on (READY)

    6. Enter the following menus: Body / Entry & Start / Active Test.

    7. Perform the Active Test according to the display on the intelligent tester.

      Entry & Start
      Tester Display Test Part Control Range Diagnostic Note
      Power / Engine SW Light Power switch illumination ON/OFF -