REAR DOOR LOCK REMOVAL


  1. REMOVE REAR NO. 2 FLOOR BOARD


    1. A01JB5ZE01

      Disengage the 2 guides <A> as shown in the illustration.

    2. Disengage the 3 guides <B> and remove the rear No. 2 floor board.

  2. REMOVE REAR DECK FLOOR BOX


    1. Remove the rear deck floor box.

  3. REMOVE REAR NO. 3 FLOOR BOARD


    1. A01JC33

      Disengage the 2 guides and remove the rear No. 3 floor board.

  4. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A01JA8O

      Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug.

  5. REMOVE DOOR ASSIST GRIP COVER


    1. A01JAP6

      Using a moulding remover, disengage the 6 claws, 2 clips and 3 guides, and remove the door assist grip cover.

  6. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. A01JBGI

      Disengage the 7 claws and 2 guides.

    2. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.

  7. REMOVE REAR DOOR ARMREST COVER


    1. A01JBG5

      Remove the rear door armrest cover.

  8. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01JCQBE01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the rear door panel.

    2. A01JC69

      Remove the 2 screws.

    3. Using a clip remover, disengage the 8 clips.

    4. Pull out the rear door trim board sub-assembly in the direction indicated by the arrow in the illustration.

    5. Raise the rear door trim board sub-assembly and remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.

    6. A01J8OM

      Disengage the 2 claws and disconnect the rear door inside handle sub-assembly.

    7. for 8 Speakers:


      1. Disconnect the connector.

  9. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. A01JBD3

      Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly, and remove the rear door inside handle sub-assembly.

  10. REMOVE REAR DOOR TRIM BRACKET


    1. A01JAN5

      Remove the 2 screws and rear door trim bracket.

  11. REMOVE REAR DOOR SERVICE HOLE COVER


    1. A01JCAT

      Disconnect the 2 connectors.

    2. Disengage the clamp and remove the rear door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the door.

  12. REMOVE REAR DOOR GLASS RUN


    1. A01JCIU

      Remove the rear door glass run.

  13. REMOVE REAR DOOR WINDOW GUIDE SUB-ASSEMBLY


    1. A01JA23

      Remove the screw.

    2. Remove the bolt and rear door window guide sub-assembly.

  14. REMOVE REAR DOOR REAR GUIDE SEAL


    1. A01J8Q9E01
      Text in Illustration
      *1 Temporary Screw

      Loosen the temporary screw.

    2. Remove the 2 screws and rear door rear guide seal.

    3. Remove the temporary screw from the rear door window division bar sub-assembly.

  15. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    1. Connect the rear power window regulator motor connector.

    2. Connect the power window regulator switch assembly and move the rear door glass sub-assembly so that the door glass bolts can be seen.

    3. Disconnect the power window regulator switch assembly and rear power window regulator motor connector.


      1. w/ Navigation System for HDD:

        Note

        After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.

    4. Disconnect the cable from the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    5. A01J8IL

      Remove the 2 bolts and rear door glass sub-assembly as shown in the illustration.

      Note


      • After the bolts are removed, do not allow the door glass to fall.

      • Do not damage the door glass.

  16. REMOVE REAR DOOR LOCK ASSEMBLY (w/o Double Locking System)


    1. A01JC5J

      Using a T30 "TORX" socket wrench, remove the 3 screws.

    2. Move the rear door lock assembly downward and pull the release plate out of the rear door outside handle frame.

    3. A01JDAN

      Remove the door lock wiring harness seal from the rear door lock assembly.

  17. REMOVE REAR DOOR LOCK ASSEMBLY (w/ Double Locking System)


    1. A01J8J4

      Using a T30 "TORX" socket wrench, remove the 3 screws.

    2. Move the rear door lock assembly downward and pull the release plate out of the rear door outside handle frame.

    3. A01JDAX

      Remove the door lock wiring harness seal from the rear door lock assembly.

  18. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)


    1. A01J8OJ

      Using a screwdriver, disengage the 2 claws as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01JD3H

      Remove the rear door lock remote control cable assembly as shown in the illustration.

  19. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)


    1. A01JBCM

      Using a screwdriver, disengage the 2 claws as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01JBN2

      Remove the rear door lock remote control cable assembly as shown in the illustration.

  20. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)


    1. A01J9EQ

      Using a screwdriver, disengage the 4 claws as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01JCU3

      Remove the rear door inside locking cable assembly as shown in the illustration.

  21. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)


    1. A01J9DV

      Using a screwdriver, disengage the 4 claws as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01JC4J

      Remove the rear door inside locking cable assembly as shown in the illustration.