INTELLIGENT PARKING ASSIST SYSTEM, Diagnostic DTC:C1AEE

DTC Code DTC Name
C1AEE IPA Sensor Communication Circuit

DESCRIPTION

The parking assist ECU communicates with the No. 1 ultrasonic sensor (for LH side), and the No. 1 ultrasonic sensor (for RH side) via the No. 1 ultrasonic sensor (for LH side). This DTC is stored when the parking assist ECU judges that there is an abnormality in the communication circuit to the No. 1 ultrasonic sensor (for LH side) or the No. 1 ultrasonic sensor (for RH side) that is connected via the for LH side sensor, immediately after the power switch is turned on (READY), or while the sensors are operating (neither park (P) nor reverse (R) is selected and the vehicle is not stopped).

DTC No. DTC Detection Condition Trouble Area
C1AEE Ultrasonic sensor communication bus failure

  • Harness or connector

  • No. 1 ultrasonic sensor (for LH side)

  • No. 1 ultrasonic sensor (for RH side)

  • Parking assist ECU

WIRING DIAGRAM

A01JCGKE04

INSPECTION PROCEDURE

Note


  • When the "System initializing" message is displayed on the navigation ECU sub-assembly after the auxiliary battery cable has been disconnected, correct the steering angle neutral point Click here.

  • Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the intelligent parking assist system may be needed Click here.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - NO. 1 ULTRASONIC SENSOR (for LH SIDE))


    1. Disconnect the L151 connector from the parking assist ECU.

    2. Disconnect the C2 connector from the No. 1 ultrasonic sensor (for LH side).

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L151-1 (CSB3) - Body ground Always 10 kΩ or higher
      L151-19 (LIN3) - Body ground Always 10 kΩ or higher
      L151-2 (CSG3) - Body ground Always 10 kΩ or higher
      L151-1 (CSB3) - C2-1 (BI) Always Below 1 Ω
      L151-19 (LIN3) - C2-3 (SI) Always Below 1 Ω
      L151-2 (CSG3) - C2-5 (EI) Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. CHECK NO. 1 ULTRASONIC SENSOR (for LH SIDE)


    1. Remove the No. 1 ultrasonic sensor (for LH side) Click here.

    2. A01JA7TE01
      Text in Illustration
      *a

      Component without harness connected

      (No. 1 Ultrasonic Sensor (for LH Side))

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (BI) - 5 (EI) Always 10 kΩ or higher
      1 (BI) - 2 (BO) Always 10 kΩ or higher
      3 (SI) - 4 (SO) Always Below 1 Ω
      5 (EI) - 6 (EO) Always Below 1 Ω

    NG

    REPLACE NO. 1 ULTRASONIC SENSOR (for LH SIDE) Click here

    OK

  3. CHECK HARNESS AND CONNEC (NO. 1 ULTRASONIC SENSOR (for LH SIDE) - NO. 1 ULTRASONIC SENSOR (for RH SIDE))


    1. Disconnect the C2 connector from the No. 1 ultrasonic sensor (for LH side).

    2. Disconnect the C1 connector from the No. 1 ultrasonic sensor (for RH side).

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C2-2 (BO) - C1-1 (BI) Always Below 1 Ω
      C2-4 (SO) - C1-3 (SI) Always Below 1 Ω
      C2-6 (EO) - C1-5 (EI) Always Below 1 Ω
      C2-2 (BO) - Body ground Always 10 kΩ or higher
      C2-4 (SO) - Body ground Always 10 kΩ or higher
      C2-6 (EO) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. REPLACE NO. 1 ULTRASONIC SENSOR (for LH SIDE)


    1. Replace the No. 1 ultrasonic sensor (for LH side) with a known good sensor Click here.


    NEXT

  5. CHECK DTC OUTPUT


    1. Clear the DTCs Click here.

    2. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC C1AEE is output A
      DTCs are not output B

    B

    END (for LH SIDE SENSOR WAS DEFECTIVE)

    A

  6. REPLACE NO. 1 ULTRASONIC SENSOR (for RH SIDE)


    1. Replace the No. 1 ultrasonic sensor (for RH side) with a known good sensor Click here.


    NEXT

  7. CHECK DTC OUTPUT


    1. Clear the DTCs Click here.

    2. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC C1AEE is output A
      DTCs are not output B

    B

    END (for RH SIDE SENSOR WAS DEFECTIVE)

    A

    REPLACE PARKING ASSIST ECU Click here