BRAKE BOOSTER (for LHD) REMOVAL


  1. PRECAUTION (w/ Navigation System for HDD)

    Note

    After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and setting. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.

  2. REMOVE REAR NO. 2 FLOOR BOARD


    1. A01JB5ZE01

      Disengage the 2 guides <A> as shown in the illustration.

    2. Disengage the 3 guides <B> and remove the rear No. 2 floor board.

  3. REMOVE REAR DECK FLOOR BOX


    1. Remove the rear deck floor box.

  4. REMOVE REAR NO. 3 FLOOR BOARD


    1. A01JC33

      Disengage the 2 guides and remove the rear No. 3 floor board.

  5. DISABLE BRAKE CONTROL


    1. Wait at least 2 minutes after the power switch off.

      Note

      When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.

    2. A01JAIJ

      Disconnect the reservoir level switch connector with the parking brake applied.

    3. Disconnect the cable from the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    4. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

    5. Check that the brake pedal can not be further depressed.

    6. Release the parking brake.

  6. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A01JB1P

      Remove the 2 screws <D>.

    2. Disengage the claw and guide.

    3. Disconnect each connector and remove the No. 1 instrument panel under cover sub-assembly.

  7. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

    Tech Tips

    Refer to the procedure up to Remove Windshield Wiper Motor And Link Assembly Click here.

  8. REMOVE COWL BODY MOUNTING REINFORCEMENT LH


    1. A01JAL3

      Remove the 3 bolts and cowl body mounting reinforcement LH.

  9. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY


    1. A01JCF9

      Disengage the clamp and separate the wire harness.

    2. A01J9NS

      Disengage the claw and bend the No. 1 heater air duct splash shield seal.

    3. A01JC64

      Disengage the claw and bend the water guard plate RH.

    4. A01J9P5

      Remove the 9 bolts and outer cowl top panel sub-assembly.

  10. DRAIN BRAKE FLUID

    Note

    If brake fluid leaks onto any painted surface, immediately wash it off.

  11. REMOVE BRAKE PEDAL RETURN SPRING


    1. A01JCI1

      Remove the brake pedal return spring from the brake pedal support sub-assembly and push rod pin.

  12. REMOVE PUSH ROD PIN


    1. A01J9SJ

      Remove the clip and push rod pin to separate the brake pedal sub-assembly from the push rod clevis.

  13. SEPARATE BRAKE MASTER CYLINDER RESERVOIR WITH BRACKET


    1. A01JBYA

      Remove the 2 nuts and separate the brake master cylinder reservoir with bracket.

  14. DISCONNECT NO. 1 RESERVOIR HOSE


    1. A01JCD3E01
      Text in Illustration
      *1 No. 1 Reservoir Hose
      *2 No. 2 Reservoir Hose

      Move the 2 clips and disconnect the No. 1 reservoir hose and No. 2 reservoir hose from the brake booster with master cylinder assembly.

  15. DISCONNECT NO. 2 RESERVOIR HOSE

  16. DISCONNECT BRAKE ACTUATOR HOSE


    1. A01JA5B

      Move the clip and disconnect the brake actuator hose from the brake booster pump assembly.

  17. REMOVE BRAKE MASTER CYLINDER RESERVOIR WITH BRACKET

  18. REMOVE NO. 5 BRAKE ACTUATOR BRACKET


    1. A01JBXI

      Disengage the clamp.

    2. Remove the 2 nuts and No. 5 brake actuator bracket.

  19. REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY


    1. A01J9NB

      Release the lock lever and disconnect the connector from the brake booster with master cylinder assembly.

      Note

      Be careful not to allow the brake fluid to enter the removed connector.

      Tech Tips

      Perform this step only when the connector has not been disconnected.

    2. A01JDC7

      Remove the 2 bolts and No. 2 brake tube clamp bracket from the brake booster with master cylinder assembly.

    3. A01JA9EE01

      Using a union nut wrench, disconnect the 5 brake lines from the brake booster with master cylinder assembly.

    4. Use tags or make a memo to identify the places to reconnect.

      Text in Illustration
      *1 to Front Wheel Cylinder LH
      *2 to Rear Wheel Cylinder RH
      *3 to Brake Booster Pump Assembly
      *4 to Rear Wheel Cylinder LH
      *5 to Front Wheel Cylinder RH
    5. A01J9R4

      Disengage the 2 clamps and separate the brake line.

    6. A01JAFFE01
      Text in Illustration
      *1 Connector Portion
      *2 Union
      *3 Push Rod Clevis and Boot
      *4 Front No. 2 Brake Tube

      Remove the 4 nuts and brake booster with master cylinder assembly.

      Note


      • Do not kink or damage the brake lines.

      • Do not carry the brake booster with master cylinder assembly by the portion shown in the illustration.

  20. REMOVE BRAKE BOOSTER GASKET