REAR COIL SPRING INSTALLATION


  1. INSTALL REAR UPPER COIL SPRING INSULATOR LH


    1. A01J924E01
      Text in Illustration
      *1 10 mm or less

      Install the rear upper coil spring insulator LH to the rear coil spring LH.

      Note

      Install the rear upper coil spring insulator so that the dimension between the stopper and the upper end of the rear coil spring is 10 mm (0.394 in.) or less.

  2. INSTALL REAR UPPER COIL SPRING INSULATOR RH

    Tech Tips

    Perform the same procedure as the LH side.

  3. INSTALL REAR LOWER COIL SPRING INSULATOR LH

  4. INSTALL REAR LOWER COIL SPRING INSULATOR RH

  5. INSTALL REAR COIL SPRING LH


    1. Support the spring seat of the rear axle beam assembly using 2 jacks and 2 wooden blocks.

      A01JB1ZE01
      Text in Illustration
      *1 Jack *2 Wooden Block

    2. Remove the 2 bolts while holding the 2 nuts and separate the rear axle beam assembly from the rear shock absorber assemblies LH and RH.

      Note

      Since the stopper nuts are used, turn the bolts.

    3. Slowly lower the rear axle beam assembly using 2 jacks and 2 wooden blocks.

    4. A01JANCE01
      Text in Illustration
      *1 Identification Mark
      *2 30° or less

      Set the rear coil spring LH to the rear axle beam assembly.

      Note

      Set the rear coil spring so that the identification marks are positioned as shown in the illustration.

    5. Slowly jack up the rear axle beam assembly using 2 jacks and 2 wooden blocks and temporarily install the rear axle beam assembly and rear coil spring LH with the 2 bolts and 2 nuts.

      A01JCNME01
      Text in Illustration
      *1 Jack *2 Wooden Block

      Note

      Since the stopper nuts are used, turn the bolts.

      Tech Tips

      Insert the bolt with the threaded end facing the outside of the vehicle.

  6. INSTALL REAR COIL SPRING RH

    Tech Tips

    Perform the same procedure as the LH side.

  7. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH (w/ Height Control Sensor)


    1. A01JAZB

      Install the rear height control sensor sub-assembly RH to the rear axle beam assembly with the bolt.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  8. INSTALL REAR SPEED SENSOR WIRE (for LH Side)


    1. A01JB59

      Install the rear speed sensor wire to the rear axle beam assembly with the nut and 2 clamps.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note

      Do not twist the rear speed sensor wire when installing it.

  9. INSTALL REAR SPEED SENSOR WIRE (for RH Side)

    Tech Tips

    Perform the same procedure as the LH side.

  10. CONNECT REAR SPEED SENSOR WIRE (for LH Side)


    1. A01JAGB

      Connect the rear speed sensor wire connector to the rear speed sensor.

  11. CONNECT REAR SPEED SENSOR WIRE (for RH Side)

    Tech Tips

    Perform the same procedure as the LH side.

  12. INSTALL REAR WHEELS

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

  13. STABILIZE SUSPENSION


    1. Lower the vehicle.

    2. Bounce the vehicle up and down several times to stabilize the suspension.

  14. FULLY TIGHTEN REAR AXLE BEAM ASSEMBLY


    1. A01J9K2E01
      Text in Illustration
      *1 LH Side
      *2 RH Side

      Fully tighten the 2 bolts.

      Torque:
      135 N*m  { 1377 kgf*cm, 100 ft.*lbf }

      Note

      The final torque must be applied under the standard vehicle height conditions.

    2. A01J93FE01
      Text in Illustration
      *1 LH Side
      *2 RH Side

      Fully tighten the 2 bolts.

      Torque:
      90 N*m  { 918 kgf*cm, 66 ft.*lbf }

      Note


      • Since the stopper nut are used, turn the bolts.

      • The final torque must be applied under the standard vehicle height conditions.

  15. INSTALL REAR WHEEL HOUSE LINER LH


    1. A01JAP1

      Install the rear wheel house liner LH with the clip.

  16. INSTALL REAR WHEEL HOUSE LINER RH

    Tech Tips

    Perform the same procedure as the LH side.

  17. INSPECT REAR WHEEL ALIGNMENT

    Click here.

  18. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

  19. PERFORM YAW RATE AND ACCELERATION SENSOR CALIBRATION

    Click here.

  20. CHECK FOR SPEED SENSOR SIGNAL

    Click here.

  21. PERFORM INITIALIZATION (w/ Height Control Sensor)

    Note

    Some systems need to be initialized after the rear height control sensor sub-assembly RH is replaced Click here.