REAR AXLE HUB BOLT REPLACEMENT

Note

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be output. As there is no malfunction, delete the DTC.

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.


  1. PRECAUTION (w/ Navigation System for HDD)

    Note

    After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and setting. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.

  2. REMOVE REAR NO. 2 FLOOR BOARD


    1. A01JB5ZE01

      Disengage the 2 guides <A> as shown in the illustration.

    2. Disengage the 3 guides <B> and remove the rear No. 2 floor board.

  3. REMOVE REAR DECK FLOOR BOX


    1. Remove the rear deck floor box.

  4. REMOVE REAR NO. 3 FLOOR BOARD


    1. A01JC33

      Disengage the 2 guides and remove the rear No. 3 floor board.

  5. DISABLE BRAKE CONTROL


    1. Wait at least 2 minutes after the power switch off.

      Note

      When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.

    2. A01JAIJ

      Disconnect the reservoir level switch connector with the parking brake applied.

    3. Disconnect the cable from the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    4. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

    5. Check that the brake pedal can not be further depressed.

    6. Release the parking brake.

  6. REMOVE REAR WHEEL

  7. REMOVE FRONT DOOR SCUFF PLATE LH (for LHD)


    1. A01JB0N

      Disengage the 10 claws and remove the front door scuff plate LH.

  8. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH (for LHD)


    1. A01J99M

      Remove the clip.

    2. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.

  9. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY (for LHD)


    1. A01JA5Y

      Remove the screw <C>.

    2. A01JCRX

      Disengage the 6 claws and clip as shown in the illustration.

    3. A01J9TK

      Disengage the claw and 2 guides and disconnect the hood lock control cable.

    4. Disconnect each connector and clamp, and remove the lower instrument panel finish panel assembly.

  10. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    1. A01JA4G

      Remove the screw <D>.

    2. Disengage the 2 claws and guide.

    3. Disconnect each connector and remove the No. 1 instrument panel under cover sub-assembly.

  11. LOOSEN PARKING BRAKE CABLE


    1. Completely release the parking brake pedal.

    2. A01JCHVE01
      Text in Illustration
      *1 Lock Nut
      *2 Adjusting Nut

      Loosen the lock nut and adjusting nut to completely release the parking brake cable.

  12. DISCONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY


    1. A01JBJ2E01

      Separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.

    2. A01JBJGE03
      Text in Illustration
      *1 No. 3 Parking Brake Cable Assembly
      *2 Clip
      *3 Offset Wrench (14 mm)

      Separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.

      Tech Tips

      Insert an offset wrench (14 mm) at the base of the No. 3 parking brake cable assembly as shown in the illustration to disengage the clip. Pull out the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.

  13. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY


    1. A01J99G

      Remove the 2 bolts, and separate the rear disc brake caliper assembly.

      Note

      Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.

  14. REMOVE REAR DISC


    1. A01JBWME03
      Text in Illustration
      *1 Matchmark

      Remove the rear disc.

      Tech Tips

      Place matchmarks on the disc and axle hub.

  15. REMOVE REAR AXLE HUB BOLT


    1. A01JAXTE01
      Text in Illustration
      *1 Nut

      Temporarily install 2 nuts to the rear axle hub bolt as shown in the illustration.

      Recommended service nut
      Thread diameter: 12.0 mm (0.472 in.)
      Thread pitch: 1.5 mm (0.0591 in.)

      Note

      Install the nuts to prevent damage to the hub bolts.

    2. Using SST and a brass bar or an equivalent tool to hold the rear axle hub and bearing assembly, remove the rear axle hub bolt.

      SST
      09611-12010

      Note

      Do not damage the threads of the rear axle hub bolts.

  16. INSTALL REAR AXLE HUB BOLT


    1. A01JCN1E01
      Text in Illustration
      *1 Nut
      *2 Washer

      Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly.

    2. Install a washer and nut to the new rear axle hub bolt as shown in the illustration.

      Recommended service nut
      Thread diameter: 12.0 mm (0.472 in.)
      Thread pitch: 1.5 mm (0.0591 in.)

      Tech Tips

      The thickness of the washer is preferably 5 mm (0.197 in.) or more.

    3. Using a brass bar or an equivalent tool to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the nut.

      Note


      • Install the nuts to prevent damage to the hub bolts.

      • Do not damage the threads of the rear axle hub bolts.

    4. Remove the 3 nuts and washer from the 3 rear axle hub bolts.

  17. INSTALL REAR DISC


    1. A01JBWME03
      Text in Illustration
      *1 Matchmark

      Align the matchmarks of the disc and axle hub, and install the disc.

      Note

      When replacing the disc with a new one, select the installation position where the rear disc has minimal runout.

  18. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY


    1. A01J99G

      Install the rear disc brake caliper assembly with the 2 bolts.

      Torque:
      57 N*m  { 585 kgf*cm, 42 ft.*lbf }

  19. CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY


    1. A01JCHFE03
      Text in Illustration
      *1 No. 3 Parking Brake Cable Assembly
      *2 Clip

      Install the No. 3 parking brake cable assembly to the rear disc brake cylinder assembly.

      Tech Tips

      Be sure to engage the No. 3 parking brake cable assembly clip onto the rear disc brake cylinder assembly as shown in the illustration.

    2. A01JBJ2E02

      Connect the No. 3 parking brake cable assembly to the rear disc brake cylinder assembly.

  20. ADJUST PARKING BRAKE

    Tech Tips

    Click here

  21. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY (for LHD)


    1. Connect each connector.

    2. Engage the clamp.

    3. A01J9TK

      Engage the 2 guides and claw to connect the hood lock control cable.

    4. A01J9Q6

      Engage the 6 claws and clip.

    5. A01JA5Y

      Install the lower instrument panel finish panel assembly with the screw <C>.

  22. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH (for LHD)


    1. A01J99M

      Engage the 2 clips.

    2. Install the cowl side trim board LH with the clip.

  23. INSTALL FRONT DOOR SCUFF PLATE LH (for LHD)


    1. A01JB0N

      Engage the 10 claws to install the front door scuff plate LH.

  24. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    1. Connect each connector.

    2. A01JA4G

      Engage the guide and 2 claws.

    3. Install the No. 1 instrument panel under cover sub-assembly with the screw <D>.

  25. INSTALL REAR WHEEL

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

  26. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


    1. Connect the cable to the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    2. Connect the reservoir level switch connector.

    3. Clear the DTCs Click here.

  27. INSTALL REAR NO. 3 FLOOR BOARD


    1. A01JC33

      Engage the 2 guides to install the rear No. 3 floor board.

  28. INSTALL REAR DECK FLOOR BOX


    1. Install the rear deck floor box.

  29. INSTALL REAR NO. 2 FLOOR BOARD


    1. A01JCWRE01

      Engage the 3 guides <A>.

    2. Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.