RADIATOR REMOVAL


  1. PRECAUTION (w/ Navigation System for HDD)

    Note

    After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.

  2. REMOVE RADIATOR SUPPORT OPENING COVER


    1. A01JBUM

      Remove the 3 clips.

    2. Disengage the 2 claws and remove the radiator support opening cover.

  3. REMOVE REAR NO. 2 FLOOR BOARD


    1. A01JB5ZE01

      Disengage the 2 guides <A> as shown in the illustration.

    2. Disengage the 3 guides <B> and remove the rear No. 2 floor board.

  4. REMOVE REAR DECK FLOOR BOX


    1. Remove the rear deck floor box.

  5. REMOVE REAR NO. 3 FLOOR BOARD


    1. A01JC33

      Disengage the 2 guides and remove the rear No. 3 floor board.

  6. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  7. REMOVE FRONT SPOILER COVER (w/ Front Spoiler)

  8. REMOVE ENGINE UNDER COVER

  9. DRAIN COOLANT (for Engine)

    Note

    Do not remove the reservoir tank cap, cylinder block drain cock plugs and radiator drain cock plug while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


    1. Loosen the radiator drain cock plug and drain the coolant.

      A01J9RAE01
      Text in Illustration
      *1 Reservoir Tank Cap *2 Radiator Drain Cock Plug

      Tech Tips

      Collect the coolant in a container and dispose of it according to the local regulations.

  10. DISCONNECT NO. 1 RADIATOR HOSE


    1. A01JASJ

      Disconnect the No. 1 radiator hose from the radiator assembly.

  11. DISCONNECT NO. 2 RADIATOR HOSE


    1. A01JA6B

      Disconnect the No. 2 radiator hose from the radiator assembly.

  12. REMOVE FRONT BUMPER ASSEMBLY


    1. A01JA91E01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the front bumper assembly.

      Tech Tips

      Use the same procedure for the RH side and LH side.

    2. A01JD2A

      Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

      Tech Tips

      Use the same procedure for the RH side and LH side.

    3. A01JCMZ

      Remove the screw.

      Tech Tips

      Use the same procedure for the RH side and LH side.

    4. A01J8PO

      Remove the 2 bolts and 4 screws.

    5. Using a clip remover, remove the 7 clips.

    6. w/ Front Spoiler:


      1. A01JB7K

        Using a clip remover, remove the 2 clips.

      2. Remove the 2 screws.

      3. Disengage the 2 guides and remove the front spoiler cover.

    7. A01JAQA

      Disengage the 3 claws and remove the front bumper assembly.

      Tech Tips

      Use the same procedure for the RH side and LH side.

    8. A01JB2B

      Pull back the side of the front bumper assembly as shown in the illustration and disconnect the connector.

      Note

      Do not apply excessive force when separating the front bumper.

    9. w/ Headlight Cleaner System:


      1. A01JD60

        Disconnect the headlight cleaner hose and drain the washer fluid.

        Tech Tips

        Use a container to collect the washer fluid.

    10. A01JA9S

      Remove the front bumper assembly as shown in the illustration.

  13. REMOVE MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System)


    1. A01JAQS

      Disconnect the connector.

    2. Remove the 5 bolts and millimeter wave radar sensor assembly.

  14. REMOVE MILLIMETER WAVE RADAR SENSOR BRACKET


    1. A01JB6V

      Remove the bolt and millimeter wave radar sensor bracket.

  15. REMOVE NO. 1 INVERTER BRACKET


    1. A01J9XB

      Remove the 3 bolts and No. 1 inverter bracket.

  16. REMOVE HOOD LOCK SUPPORT SUB-ASSEMBLY


    1. A01JDBV

      Disconnect the water by-pass hose clamp from the radiator support RH.

    2. A01JC54

      Disconnect the hood lock connector and hood lock control cable wire.

    3. Disconnect the 3 wire harness clamps.

    4. A01J9L3

      Disconnect the connector from the No. 2 cooling fan motor.

    5. A01J9Z6

      Disconnect the 2 wire harness clamps and connector from the fan shroud and cooling fan motor.

    6. A01JCX6

      Disconnect the 2 horn connectors.

    7. A01JC7H

      Remove the 2 bolts, radiator support RH and radiator support LH with the 2 cushions from the upper radiator support.

    8. A01JCOL

      Remove the 4 bolts and upper radiator support.

  17. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    1. A01JCX4

      Disconnect the air flow meter connector.

    2. Disconnect the 2 clamps and hose band, and remove the air cleaner cap sub-assembly.

    3. Remove the air cleaner filter element.

  18. REMOVE INLET AIR CLEANER ASSEMBLY


    1. A01JBRT

      Remove the 2 bolts and inlet air cleaner assembly.

  19. REMOVE AIR CLEANER CASE


    1. A01JAKM

      Separate the No. 4 water by-pass hose from the air cleaner case.

    2. Remove the 3 bolts and air cleaner case.

  20. REMOVE NO. 2 FAN SHROUD


    1. A01J98U

      Disconnect the No. 1 water by-pass hose from the radiator assembly.

    2. A01J8TE

      Disconnect the water by-pass hose from the radiator assembly.

    3. A01JBOH

      Disconnect the 6 water by-pass hose clamps from the No. 2 fan shroud.

    4. A01JC2L

      Remove the 2 bolts and No. 2 fan shroud from the radiator assembly.

  21. REMOVE RADIATOR ASSEMBLY


    1. A01JCJB

      Remove the radiator assembly with the fan shroud.

      Note

      For vehicles with the air conditioning system, do not apply any excessive force to the cooler condenser assembly or pipe when removing the radiator assembly.

    2. Remove the 2 lower radiator supports.

    3. A01J9XV

      Remove the 2 bolts.

    4. Remove the fan shroud from the radiator assembly.