CYLINDER HEAD REASSEMBLY


  1. INSTALL SPARK PLUG TUBE

    Note

    When using a new cylinder head, the spark plug tubes must be replaced.


    1. A01JCXRE05

      Apply adhesive onto the shaded area of a new spark plug tube.

      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
      Standard application width
      1.0 to 3.0 mm (0.0394 to 0.118 in.)

      Note


      • Install the spark plug tube within 3 minutes of applying adhesive.

      • Be careful not to deform the spark plug tube.

      • Be careful not to expose the seal to coolant for at least 1 hour after installing the tube.

    2. A01J9YQE04
      Text in Illustration
      *a Cylinder Head Casting Surface:

      Using a wooden block and hammer, tap in the spark plug tube to the specified protrusion height.

      Standard protrusion height
      122 mm (4.80 in.)

      Note

      To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping it.

  2. INSTALL STUD BOLT

    Note

    If a stud bolt is deformed or its threads are damaged, replace it.


    1. Using an E8 "TORX" socket, install the stud bolts.

      A01JCGUE09
      Text in Illustration
      *a Intake Side: *b Exhaust Side:
      Torque:
      9.5 N*m  { 97 kgf*cm, 84 in.*lbf }

  3. INSTALL NO. 2 STRAIGHT SCREW PLUG

    Note

    If water leaks from the straight screw plug or the plug is corroded, replace it.


    1. A01JCT5

      Using a 10 mm straight hexagon wrench, install 3 new gaskets and the 3 straight screw plugs.

      Torque:
      44 N*m  { 449 kgf*cm, 32 ft.*lbf }

  4. INSTALL VALVE SPRING SEAT


    1. Install the valve spring seats to the cylinder head.

  5. INSTALL VALVE STEM OIL SEAL


    1. A01JC4XE08
      Text in Illustration
      *a Intake Side:
      *b Exhaust Side:
      *c Gray
      *d Black

      Apply a light coat of engine oil to a new oil seal.

      Note

      Pay close attention when installing the intake and exhaust oil seals. For example, installing the intake oil seal to the exhaust side or installing the exhaust oil seal to the intake side can cause installation problems later.

      Tech Tips

      The intake valve oil seal is gray and the exhaust valve oil seal is black.

    2. A01JC3SE02
      Text in Illustration
      *a CORRECT
      *b INCORRECT

      Using SST, push on the oil seal.

      SST
      09201-41020

      Note

      Failure to use SST will cause the seal to be damaged or improperly seated.

  6. INSTALL INTAKE VALVE

    A01JD6YE01

    Tech Tips

    Type A and Type B can be distinguished by the shape of the compression spring.

    Text in Illustration
    *A Type A
    *B Type B
    *1 No. 1 Valve Rocker Arm Sub-assembly
    *2 Valve Spring Retainer
    *3 Compression Spring
    *4 Valve Lash Adjuster Assembly
    Type Compression Spring Shape
    A Straight
    B Tapered

    1. Type A:


      1. Place the cylinder head on wooden blocks.

      2. A01JC2AE15

        Apply engine oil to each valve over an area 30 mm (1.18 in.) or more from its tip, as shown in the illustration.

      3. Install the valve, compression spring and spring retainer to the cylinder head.

        Note

        Install the same parts in the same combination to the original locations.

      4. A01JD3ME02

        Using SST, compression spring and install the valve retainer locks.

        SST
        09202-70020   ( 09202-00010 )
      5. A01JCIA

        Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

        Note


        • Be careful not to damage the valve stem tip.

        • Be careful not to damage the retainer.

    2. Type B:


      1. Place the cylinder head on wooden blocks.

      2. A01JC2AE15

        Apply engine oil to each valve over an area 30 mm (1.18 in.) or more from its tip as shown in the illustration.

      3. A01JCGCE01
        Text in Illustration
        *1 Compression Spring
        *2 Valve Spring Retainer
        *3 Cylinder Head
        *a Upper Side

        Install the valve, compression spring and spring retainer to the cylinder head.

        Note


        • Install the compression spring with its taper side facing upward (towards the valve spring retainer).

        • Install the same parts in the same combination to the original locations.

      4. A01J9FLE01

        Using SST, compress the spring and install the valve retainer locks.

        SST
        09202-70020
        09202-00020
      5. A01J9PQ

        Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

        Note


        • Be careful not to damage the valve stem tip.

        • Be careful not to damage the retainer.

  7. INSTALL EXHAUST VALVE

    A01JD6YE01

    Tech Tips

    Type A and Type B can be distinguished by the shape of the compression spring.

    Text in Illustration
    *A Type A
    *B Type B
    *1 No. 1 Valve Rocker Arm Sub-assembly
    *2 Valve Spring Retainer
    *3 Compression Spring
    *4 Valve Lash Adjuster Assembly
    Type Compression Spring Shape
    A Straight
    B Tapered

    1. Type A:


      1. Place the cylinder head on wooden blocks.

      2. A01JASZE14

        Apply engine oil to each valve over an area 30 mm (1.18 in.) or more from its tip, as shown in the illustration.

      3. Install the valve, compression spring and spring retainer to the cylinder head.

        Note

        Install the same parts in the same combination to the original locations.

      4. A01JAF0E02

        Using SST, compression spring and install the valve retainer locks.

        SST
        09202-70020   ( 09202-00010 )
      5. A01JD9V

        Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

        Note


        • Be careful not to damage the valve stem tip.

        • Be careful not to damage the retainer.

    2. Type B:


      1. Place the cylinder head on wooden blocks.

      2. A01JASZE14

        Apply engine oil to each valve over an area 30 mm (1.18 in.) or more from its tip as shown in the illustration.

      3. A01JCGCE01
        Text in Illustration
        *1 Compression Spring
        *2 Valve Spring Retainer
        *3 Cylinder Head
        *a Upper Side

        Install the valve, compression spring and spring retainer to the cylinder head.

        Note


        • Install the compression spring with its taper side facing upward (towards the valve spring retainer).

        • Install the same parts in the same combination to the original locations.

      4. A01J8R9E01

        Using SST, compress the spring and install the valve retainer locks.

        SST
        09202-70020
        09202-00020
      5. A01JD5Y

        Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

        Note


        • Be careful not to damage the valve stem tip.

        • Be careful not to damage the retainer.