HYBRID CONTROL SYSTEM, Diagnostic DTC:P0A60-288, P0A60-290, P0A60-294, P0A60-501, P0A63-296, P0A63-298, P0A63-302, P0A63-502

DTC Code DTC Name
P0A60-288 Drive Motor "A" Phase V Current
P0A60-290 Drive Motor "A" Phase V Current
P0A60-294 Drive Motor "A" Phase V Current
P0A60-501 Drive Motor "A" Phase V Current
P0A63-296 Drive Motor "A" Phase W Current
P0A63-298 Drive Motor "A" Phase W Current
P0A63-302 Drive Motor "A" Phase W Current
P0A63-502 Drive Motor "A" Phase W Current

DESCRIPTION

The MG ECU located in the inverter with converter assembly monitors the motor inverter current sensors. P0A60 and P0A63 indicate malfunctions in current sensors, and they do not indicate malfunctions in the high-voltage system.

Tech Tips

The term "drive motor A" indicates MG2.

DTC No. INF Code DTC Detection Condition Trouble Area
P0A60 288 Malfunction in motor inverter current sensor (phase V sub sensor) Inverter with converter assembly
P0A60 290 Malfunction in motor inverter current sensor (phase V main sensor)
P0A60 294 Malfunction in motor inverter current sensor (performance problem or open phase V)
P0A60 501 Malfunction in motor inverter current sensor (phase V main and sub sensors offset)
P0A63 296 Malfunction in motor inverter current sensor (phase W sub sensor)
P0A63 298 Malfunction in motor inverter current sensor (phase W main sensor)
P0A63 302 Malfunction in motor inverter current sensor (performance problem or open phase W)
P0A63 502 Malfunction in motor inverter current sensor (phase W main and sub sensors offset)

INSPECTION PROCEDURE

Tech Tips

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


  1. Turn the power switch on (IG) and wait for 5 seconds or more.

  2. Turn the power switch on (READY) with park (P) selected and wait for 5 seconds or more.

  3. Move the shift lever to N and wait for 5 seconds or more.

  4. Depress the accelerator pedal of the vehicle with the engine stopped and park (P) selected to start the engine.

  5. Drive the vehicle forward with drive (D) selected for 5 m or more.

  6. Drive the vehicle backward with reverse (R) selected for 5 m or more.

PROCEDURE


  1. CHECK DTC OUTPUT (HV)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Check if DTCs are output.

      Result
      Result Proceed to
      Only DTC P0A60 or P0A63 are output or any DTCs other than P0A78-202 is also output. A
      P0A78-202 is output. B

    5. Turn the power switch off.


    B

    GO TO DTC CHART Click here

    A

  2. CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

    CAUTION:

    Be sure to wear insulated gloves.


    1. A01JCYY

      Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

      Note

      Before disconnecting the connector, confirm that it is properly connected by checking that the locking claws are engaged and that the connector does not pull out.

    2. Check the connection of the low voltage connector of the inverter with converter assembly.

      OK
      The connector is connected securely and there are no contact problems.

      Tech Tips

      When connecting the connector, insert it with the locking lever in the raised position. Rotate the lever downward and make sure that the connector is pulled into its socket. When the locking lever is in its fully closed position, a click will be heard as its locking claws engage. After the click is heard, pull up on the connector to confirm that it is properly connected.


    NG

    CONNECT SECURELY

    OK

  3. CHECK INVERTER WITH CONVERTER ASSEMBLY


    1. Check the installation position of the part No. label on the inverter with converter assembly Click here.

    2. Check the part number of the inverter with converter assembly.

      Result
      Result Proceed to
      Installation Position of Part No. Label Part No.
      Front - A
      Top

      • G9200-47140

      • G9200-47141

      • G9200-47180

      • G9200-47181
      Other than above. B

    B

    CHECK DTC OUTPUT (HV) Click here

    A

  4. CHECK DTC OUTPUT (HV)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Check if DTCs are output.

      Result
      Result Proceed to
      DTC P0A78-284 or P0A78-286 is also output. A
      Other than above. B

    5. Turn the power switch off.


    B

    REPLACE MG CONTROL COMPUTER AND INVERTER CURRENT SENSOR AND INVERTER WIRE Click here

    A

    REPLACE MG CONTROL COMPUTER AND INVERTER CURRENT SENSOR AND INVERTER WIRE AND POWER MODULE INTELLIGENT TRANSISTOR KIT Click here

  5. CHECK DTC OUTPUT (HV)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Check if DTCs are output.

      Result
      Result Proceed to
      DTC P0A78-284 or P0A78-286 is also output. A
      Other than above. B

    5. Turn the power switch off.


    B

    REPLACE MG CONTROL COMPUTER AND INVERTER CURRENT SENSOR Click here

    A

    REPLACE MG CONTROL COMPUTER AND INVERTER CURRENT SENSOR AND POWER MODULE INTELLIGENT TRANSISTOR KIT Click here