REPAIR INSTRUCTION CUSTOMIZE PARAMETERS

Note


  • When the customer requests a change in a function, first make sure that the function can be customized.

  • Be sure to make a note of the current settings before customizing.

  • When troubleshooting a function, first make sure that the function is set to the default setting.

Tech Tips

The following items can be customized.


  1. POWER DOOR LOCK CONTROL SYSTEM


    1. Customizing with the intelligent tester

      Illuminated Entry
      Display Default Content Setting
      Lighting Time 15 s Function that changes the lighting time after closing all doors. (It will quickly fade out in case of turning the power switch from off to on (ACC) or (IG).) 7.5 s, 15 s or 30 s

    2. Customizing function with multi-display (w/ Navigation System)


      1. Turn the power switch on (IG).

      2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Light Settings

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Interior Lights Off Timer 15 sec. Function that changes the lighting time after closing all doors. (It will quickly fade out in case of turning the power switch from off to on (ACC) or (IG).) Off, 7.5 sec., 15 sec. or 30 sec. Main body ECU (Multiplex network body ECU)

  2. WIRELESS DOOR LOCK CONTROL SYSTEM


    1. Customizing with the intelligent tester

      Wireless Door Lock Control System
      Display (item) Default Function Setting
      Wireless Control ON Function that turns wireless door lock function on or off ON or OFF
      Hazard Answer Back ON

      When the doors are locked by wireless operation, the hazard warning lights flash once.

      When the doors are unlocked by wireless operation, the hazard warning lights flash twice.

      		 ON or OFF
      Open Door Warning ON The buzzer sounds when lock is pressed when any of the doors are ajar. ON or OFF
      Panic Function*1 ON Function to operate theft deterrent system by continuously pressing panic switch on transmitter for 0.8 seconds ON or OFF
      Auto Lock Time 30 s Function that regulates the interval between unlocking and automatic relocking of doors 30 s, 60 s or 120 s
      Wireless Buzzer Resp*2 ON Wireless door lock buzzer response ON or OFF
      Wireless Buzzer Vol Level7 Wireless door lock buzzer volume Level7, Level6, Level5, Level4, Level3, Level2, Level1 or Level0

      • *1: w/ Panic Function

      • *2: for Australia

      Illuminated Entry
      Display Default Content Setting
      Lighting Time 15 s Changes the lighting time after closing all doors. (It will quickly fade out in case of turning the power switch from off to on (ACC or IG).) 7.5 s, 15 s or 30 s

    2. Customizing with the multi-display (for Navigation Receiver Type)


      1. Turn the power switch on (IG).

      2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Door Lock Settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Auto Relock Timer 30 s Function that regulates the interval between unlocking and automatic relocking of doors 30 s, 60 s or 120 s Main body ECU (Multiplex network body ECU)
        Lock/Unlock Feedback-Lights On

        When the doors are locked by wireless operation, the hazard warning lights flash once.

        When the doors are unlocked by wireless operation, the hazard warning lights flash twice.

        		 On or Off Main body ECU (Multiplex network body ECU)
        Lock/Unlock Feedback-Tone 7 Wireless door lock buzzer volume Off, 1, 2, 3, 4, 5, 6 or 7 Main body ECU (Multiplex network body ECU)

      4. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Light Settings

      5. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Interior Lights Off Timer 15 sec. Changes the lighting time after closing all doors. (It will quickly fade out in case of turning the power switch from off to on (ACC or IG).) Off, 7.5 sec., 15 sec. or 30 sec. Main body ECU (Multiplex network body ECU)

    3. Customizing with the multi-display (for Radio and Display Type)


      1. Turn the power switch on (IG).

      2. Enter the following menus: SETUP / Vehicle / Vehicle Settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Lock Feedback Volume 7 Wireless door lock buzzer volume Off, 1, 2, 3, 4, 5, 6 or 7 Main body ECU (Multiplex network body ECU)

  3. ENTRY AND START SYSTEM (for Entry Function)


    1. Customizing with the intelligent tester

      Entry & Start
      Tester Display Default Content Setting
      Park Wait Time 2.5 s Function that sets waiting time to permit opening door after door is locked with entry lock function 0.5 s, 1.5 s, 2.5 s or 5 s
      Ignition Available Area All Function that switches the entry hybrid vehicle control system start detection area Front or All
      Back Door Opening Operation* Long Function that opens the back door when the driver has the key and presses back door opener switch assembly (opener switch) Long, Twice or OFF

      *: w/ Entry System Back Door Open Function

      Warning
      Tester Display Default Content Setting
      Key Low Battery Warning ON Function that warns driver that the key battery is weak ON or OFF

    2. Customizing with the multi-display (for Radio and Display Type)


      1. Turn the power switch on (IG).

      2. Enter the following menus: SETUP / Vehicle.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Entry and start system On Function that enables or disables the smart key system. On or Off Certification ECU (smart key ECU assembly)

    3. Customizing with the multi-display (for Navigation Receiver Type)


      1. Turn the power switch on (IG).

      2. Enter the following menus: SETUP / Vehicle / Vehicle customization / Door lock settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Entry and start system On Function that enables or disables the smart key system. On or Off Certification ECU (smart key ECU assembly)

  4. ELECTRICAL KEY CANCEL (ENTRY AND START SYSTEM (for Entry Function))

    The electrical key cancel operation disables the following functions:


    • Entry Unlock/Lock

    • Entry Hybrid Vehicle Control System Start

    • Entry System Back Door Open Function*

      *: w/ Entry System Back Door Open Function

    • Electrical Key Lock-in Prevention

    • Warning


    1. The operation procedure is as follows:

      Precondition:

      Power switch off, driver door closed and unlocked.


      1. Push the unlock switch of the key once.

      2. Open the driver door within 5 seconds.

      3. Push the unlock switch of the key twice within 5 seconds.

      4. Close and open the driver door twice within 30 seconds.

        (Driver door: Close → Open → Close → Open)

      5. Push the unlock switch of the key twice within 5 seconds.

      6. Close and open the driver door within 30 seconds.

        (Driver door: Close → Open)

      7. Close the driver door within 5 seconds.

        When electrical key cancel is activated, the wireless door lock buzzer sounds twice.

        To return to the original condition, perform the procedure again. When the original condition is returned, the wireless door lock buzzer sounds once.

  5. ENTRY AND START SYSTEM (for Start Function)


    1. Customizing with the intelligent tester

      Entry & Start
      Tester Display Default Content Setting
      Ignition Available Area (Entry ignition available area) All Function to choose the available area for electrical key to start the hybrid control system. Front or All

    2. Customizing with the multi-display (for Radio and Display Type)


      1. Turn the power switch on (IG).

      2. Enter the following menus: SETUP / Vehicle.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Entry and Start System On Function that enables or disables the entry and start system. On or Off Certification ECU (smart key ECU assembly)

    3. Customizing with the multi-display (for Navigation Receiver Type)


      1. Turn the power switch on (IG).

      2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Door Lock Settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Entry and Start System On Function that enables or disables the entry and start system. On or Off Certification ECU (smart key ECU assembly)

  6. CUSTOMIZING FUNCTION WITHOUT INTELLIGENT TESTER (ENTRY AND START SYSTEM (for Start Function))

    Performing the following procedure disables the entry and start system.

    Tech Tips

    To start the hybrid control system while the entry and start system is disabled, follow the procedure for when the key battery is low Click here.


    1. The operation procedure is as follows:

      Precondition:

      Power switch off, driver door closed and unlocked.


      1. Push the unlock switch of the key once.

      2. Open the driver door within 5 seconds.

      3. Push the unlock switch of the key twice within 5 seconds.

      4. Close and open the driver door twice within 30 seconds.

        (Driver door: Close → Open → Close → Open)

      5. Push the unlock switch of the key twice within 5 seconds.

      6. Close and open the driver door within 30 seconds.

        (Driver door: Close → Open)

      7. Close the driver door within 5 seconds.

        When electrical key cancel is activated, the wireless door lock buzzer sounds twice.

        To return to the original condition, perform the procedure again. When the original condition is returned, the wireless door lock buzzer sounds once.

  7. THEFT DETERRENT SYSTEM

    Theft Deterrent System
    Display(Item) Default Content Setting
    Mech. Key Entry Alarm Cancel OFF Function that makes it possible to cancel the alarm with an unlock operation using the mechanical key. ON / OFF

  8. LIGHTING SYSTEM (LIGHTING INT)


    1. Customizing with the intelligent tester

      Illuminated Entry
      Tester Display Default Content Setting Relevant ECU
      Lighting Time 15 s Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the power switch from off to on (ACC or IG).) 7.5 s, 15 s or 30 s Main body ECU (Multiplex network body ECU)
      I/L when ACC OFF ON Lights up power switch illumination, front interior lights, rear interior light and footwell lights when the power switch is turned from on (ACC or IG) to off. ON or OFF
      I/L ON W/Door Key Unlock ON Lights up power switch illumination, front interior lights, rear interior light and footwell lights when doors are unlocked using a mechanical key or door control transmitter. ON or OFF
      Light Control ON

      Dims (ON setting) or turns off (OFF setting) the footwell lights under the following conditions:

      Power switch on (IG), shift lever not in P, and all doors closed.

      		 ON or OFF
      Room Light when Aprchd ON Lights up the power switch illumination, front interior lights, rear interior light and footwell lights when a key enters any actuation area around the doors. ON or OFF
      Inside Foot Light ON ON/OFF of footwell light control function. ON or OFF

    2. Customizing with the multi-display (for Navigation Receiver Type)


      1. Turn the power switch on (IG).

      2. Enter the following menus: Setup / Vehicle / Vehicle Customization / Light Settings.

      3. Select the setting by referring to the table below:

        Light Settings
        Display Default Content Setting Relevant ECU
        Interior Lights Off Timer 15 sec. Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the power switch from off to on (ACC or ON).) Off, 7.5 sec., 15 sec., or 30 sec. Main body ECU (Multiplex network body ECU)

  9. METER / GAUGE SYSTEM

    Warning
    Tester Display Default Content Setting
    Key Remind Sound Slow Function to change the cycle of the key reminder buzzer Normal, Fast or Slow
    Driver Side Seatbelt Warning Buzzer*1 ON Function to turn on/off the seat belt warning buzzer ON or OFF
    Front Passenger Side Seatbelt Warning Buzzer*1 ON Function to turn on/off the seat belt warning buzzer ON or OFF
    Rear Seatbelt Warning Buzzer*2 ON Function to turn on/off the rear seat belt warning buzzer ON or OFF
    Reverse Buzzer Continual Function to change the type of the reverse warning buzzer Single or Continual

    • *1: This setting is only valid for the buzzer which sounds at 20 km/h (12 mph) or more.

    • *2: w/ Rear Seat Belt Warning

  10. SEAT BELT WARNING SYSTEM

    Combination Meter
    Tester Display Default Content Setting
    Driver Side Seatbelt Warning Buzzer ON Function to sound the seat belt warning buzzer ON / OFF
    Front Passenger Side Seatbelt Warning Buzzer ON Function to sound the seat belt warning buzzer ON / OFF
    Rear Seat Belt Warning Buzzer* ON Function to sound the seat belt warning buzzer ON / OFF

    • *: w/ Rear Seat Belt Warning

  11. AIR CONDITIONING SYSTEM


    1. Customizing with the intelligent tester

      Air Conditioner
      Display (Item) Default Content Setting
      Set Temperature Shift Normal Function to control the shifted temperature against the displayed temperature. -2C, -1C, Normal, +1C, +2C
      Air inlet Mode Automatic In case of turning the A/C ON to cool the cabin down quickly, this is the function to change the mode automatically to RECIRCULATION mode Automatic or Manual
      Foot/DEF Auto Mode ON Function to automatically turn the airflow from FOOT/DEF on when AUTO mode is on. ON or OFF
      Foot/DEF Automatic Blow Up Function ON Function to automatically increase the blower level when the defroster is on. ON or OFF
      Ambient Temperature Shift Normal Function to control the shifted ambient temperature in relation to the displayed ambient temperature. -3C, -2C, -1C, Normal, +1C, +2C, +3C
      ECO MODE Cancel OFF Function to cancel the ECO drive mode when item is on. OFF or ON
      Noise and Vibration Reduction OFF Function to change speed of the compressor when item is on. OFF or ON
      Start Pre A/C*1 Long1 Function to set the activation operation method for the remote air conditioning system using the key (electrical transmitter). 1 tim ON, 2 tim ON, Long1 or Long2
      Stop Pre A/C*1 2 tim ON Function to set the stop operation method for the remote air conditioning system using the key (electrical transmitter). 1 tim ON, 2 tim ON, Long1 or Long2

      • *1: w/ Remote Air Conditioning System

    2. Customizing with the multi-display (w/ Navigation System (for Navigation Receiver Type)


      1. Turn the power switch on (IG).

      2. Enter the following menus: SETUP / Vehicle / Vehicle settings / Climate settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Efficient Ventilation Mode On In case of turning the A/C ON to cool the cabin down quickly, this is the function to change the mode automatically to RECIRCULATION mode On or Off Air conditioning amplifier assembly

  12. POWER WINDOW CONTROL SYSTEM


    1. Customizing with the intelligent tester

      Power Window
      Tester Display Default Content Setting Relevant ECU
      P Window Auto Up Avail This function is used to enable or disable the auto up function for the front passenger door window using the power window regulator switch assembly (for front passenger door). Not Avl/Avail Power window ECU (Power window regulator motor assembly)
      P Window Auto Up From Driver Avail This function is used to enable or disable the remote auto up function for the front passenger door window using the multiplex network master switch assembly. Not Avl/Avail Power window ECU (Power window regulator motor assembly)
      RR Window Auto Up Avail This function is used to enable or disable the auto up function using the power window regulator switch assembly (for rear RH door). Not Avl/Avail Power window ECU (Power window regulator motor assembly)
      RR Window Auto Up From Driver Avail This function is used to enable or disable the remote auto up function for the rear RH door window using the multiplex network master switch assembly. Not Avl/Avail Power window ECU (Power window regulator motor assembly)
      RL Window Auto Up Avail This function is used to enable or disable the auto up function using the power window regulator switch assembly (for rear LH door). Not Avl/Avail Power window ECU (Power window regulator motor assembly)
      RL Window Auto Up From Driver Avail This function is used to enable or disable the remote auto up function for the rear LH door window using the multiplex network master switch assembly. Not Avl/Avail Power window ECU (Power window regulator motor assembly)

  13. LIGHTING SYSTEM (LIGHTING EXT)


    1. Customizing with the intelligent tester

      Light Control
      Display Default Content Setting Relevant ECU
      Disp Ex ON Sen Normal Changes the ambient brightness level required to dim the lights such as the indicator lights of the combination meter, A/C indicator light and clock.*A Light2, Light1, Normal, Dark1 or Dark2 Main Body ECU (Multiplex Network Body ECU)
      Disp Ex OFF Sen Normal Changes the ambient brightness level required to cancel the dimming of the lights such as the indicator lights of the combination meter, A/C indicator light and clock.*B Light2, Light1, Normal, Dark1 or Dark2
      Response Time 0.1 s Changes the delay timing of lighting the taillights when going into a tunnel when the light control switch is in the AUTO position 0.1 s or 1.0 s
      Sensitivity Normal Adjusts the sensitivity of the automatic light control system.*C Light2, Light1, Normal, Dark1 or Dark2
      DRL Function On ON/OFF of the DRL function On or Off

      Tech Tips

      The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.

      *A
      Brightness level required to dim the lights A01JA36
      Setting Dark2 Dark1 Normal Light1 Light2
      *B
      Brightness level required to cancel the dimming of the lights A01JA36
      Setting Dark2 Dark1 Normal Light1 Light2
      *C
      Sensitivity of the automatic light control system A01JA36
      Setting Dark2 Dark1 Normal Light1 Light2

    2. Customizing with the multi-display (for Navigation Receiver Type)


      1. Turn the power switch on (IG).

      2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Light Settings.

      3. Select the setting by referring to the table below.

        Light Settings
        Display Default Content Setting Relevant ECU
        Headlamps-On Sensitivity 0 Adjusts the sensitivity of the automatic light control system.*A -2, -1, 0, +1 or +2 Main Body ECU (Multiplex Network Body ECU)

        Tech Tips

        The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.

        *A
        Sensitivity of the automatic light control system A01JA36
        Setting -2 -1 0 +1 +2

    3. Customizing with the multi-display (for Radio and Display Type)


      1. Turn the power switch on (IG).

      2. Enter the following menus: SETUP / Vehicle.

      3. Select the setting by referring to the table below.

        Vehicle Settings
        Display Default Content Setting Relevant ECU
        Light Sensor Sensitivity 0 Adjusts the sensitivity of the automatic light control system.*A -2, -1, 0, +1 or +2 Main Body ECU (Multiplex Network Body ECU)

        Tech Tips

        The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.

        *A
        Sensitivity of the automatic light control system A01JA36
        Setting -2 -1 0 +1 +2