NAVIGATION SYSTEM (for DVD) DTC CHECK / CLEAR


  1. CHECK DTC (CHECK USING INTELLIGENT TESTER)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Navigation System / DTC.

    5. Check for DTC(s) and freeze frame data, and then write them down.

    6. Check the details of the DTC(s) Click here.

  2. CLEAR DTC (CHECK USING INTELLIGENT TESTER)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Navigation System / DTC.

    5. Clear the DTCs.

  3. START DIAGNOSTIC MODE

    Tech Tips


    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

    • To help find the malfunction when the system can not change to diagnostic mode, check for DTCs using the intelligent tester.

    • After the power switch is turned on (IG), check that the map is displayed before starting diagnostic mode. Otherwise, some items cannot be checked.


    1. There are 2 methods to start diagnostic mode. Start the mode by using either of them.

    2. A01JCZFE01

      Method 1


      1. Start the hybrid system.

      2. While pressing and holding the "INFO" switch, operate the light control switch: off → Turn on → Turn off → Turn on → Turn off → Turn on → Turn off.

      3. Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts automatically and the result will be displayed.

    3. Method 2


      1. Start the hybrid system.

      2. Press the "DISP" switch.

      3. A01J8R8E01
        A01J9GKE01

        From the display quality adjustment screen, touch the corners of the screen in the following order: Upper left → Lower left → Upper left → Lower left → Upper left → Lower left.

      4. Diagnostic mode starts and the "Service Menu" screen will be displayed.

  4. FINISH DIAGNOSTIC MODE


    1. Turn the power switch off.

  5. FAILURE DIAGNOSIS


    1. A01JC8T

      The "Failure Diagnosis" screen will be displayed by pressing the "Failure Diagnosis" switch on the "Service Menu" screen.

  6. SYSTEM CHECK


    1. A01J9UH

      The "System Check Mode" screen will be displayed by pressing the "System Check" switch on the "Failure Diagnosis" screen.

  7. CHECK DTC (CHECK USING SYSTEM CHECK MODE SCREEN)


    1. A01JBZU

      Read the system check result.


      1. If the check result is "EXCH" or "CHEK", touch the displayed check result to view the results on the "Unit Check Mode" screen and record them.

        Tech Tips


        • When all results are "OK", this means that no DTCs are present.

        • When proceeding to view the results of another device, press the "Back" switch to return to the "System Check Mode" screen. Repeat the step above to view the results of other devices.

      2. Check the details of the DTC(s) Click here.

        Note

        The navigation system outputs DTCs for the following system. When DTCs other than the codes in Diagnostic Trouble Code Chart for the navigation system are output, refer to Diagnostic Trouble Code Chart for the system.

        System Proceed to
        Intelligent parking assist system

        Click here

  8. DTC CLEAR/RECHECK (CLEAR USING SYSTEM CHECK MODE SCREEN)


    1. A01JA06

      Clear DTC


      1. Press the "Memory CLR" switch for 3 seconds.

      2. Confirm that the check results are cleared.

        Tech Tips


        • To clear the DTC for a specific device, clear the DTC using the "Unit Check Mode" screen.

        • When clearing a DTC using the "Unit Check Mode" screen, press the "Code CLR" switch for 3 seconds.

    2. A01JCLQ

      Recheck


      1. Press the "Recheck" switch.

      2. A01J9CV

        Confirm that all diagnostic codes are "OK" when the check results are displayed. If a code other than "OK" is displayed, troubleshoot again.

        Tech Tips

        When a DTC was cleared using the "Unit Check Mode" screen, press the "Back" switch to return to the "System Check Mode" screen and perform this operation.