AUDIO AND VISUAL SYSTEM Illumination Circuit

DESCRIPTION

Power is supplied to the radio and display receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

A01JAWYE03

INSPECTION PROCEDURE

Note


  • The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System Click here.

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK ILLUMINATION


    1. Check if the illumination for the radio and display receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

      Result
      Result Proceed to
      Illumination comes on for all components except steering pad switch assembly. A
      Illumination comes on for all components except radio and display receiver assembly. B
      No illumination comes on (radio and display receiver assembly, hazard switch, heater control switch, etc.). C

    B

    CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL) Click here

    C

    GO TO LIGHTING SYSTEM Click here

    A

  2. CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)


    1. Disconnect the spiral cable with sensor sub-assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      L52-12 (IL+2) - Body ground

      Power switch off

      Light control switch in the tail or head position

      		 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT STEERING PAD SWITCH ASSEMBLY


    1. Disconnect the steering pad switch assembly connector.

    2. Connect an auxiliary battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal EAU of the steering pad switch assembly connector.

      A01JD7BE02

    3. Check if the illumination for the steering pad switch assembly comes on.

      OK
      Illumination for the steering pad switch assembly comes on.
      Text in Illustration
      *a

      Component without harness connected

      (Steering Pad Switch Assembly)

      		 - -

    4. Proceed to the next step based on the inspection result.

      Result
      Result Proceed to
      NG A
      OK B

    B

    INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY Click here

    A

  4. INSPECT STEERING PAD SWITCH RH


    1. Disconnect the steering pad switch RH connectors.

      A01JC9AE20

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      SR1-2 (IL+2) - z9-5 (IL+2) Always Below 1 Ω
      SR1-5 (EAU) - z9-8 (EAU) Always Below 1 Ω
      Text in Illustration
      *a

      Component without harness connected

      (Steering Pad Switch RH)

      		 - -

    NG

    REPLACE STEERING PAD SWITCH RH Click here

    OK

    REPLACE STEERING PAD SWITCH LH Click here

  5. INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY


    1. Disconnect the steering pad switch assembly connector.

    2. Disconnect the spiral cable with sensor sub-assembly connector.

    3. A01JAXCE04
      Text in Illustration
      *a

      Component without harness connected

      (Spiral Cable with Sensor Sub-assembly)
      *b Steering Pad Switch Assembly Side
      *c Vehicle Side

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      z9-5 (IL+2) - L52-12 (IL+2) Center Below 1 Ω
      2.5 rotations to the left
      2.5 rotations to the right
      z9-8 (EAU) - L52-4 (EAU) Center Below 1 Ω
      2.5 rotations to the left
      2.5 rotations to the right

    4. After setting the spiral cable with sensor sub-assembly to the center position, rotate the spiral cable with sensor sub-assembly 2.5 times clockwise. Then while rotating the spiral cable with sensor sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      z9-5 (IL+2) - L52-12 (IL+2) Always Below 1 Ω
      z9-8 (EAU) - L52-4 (EAU) Always Below 1 Ω

      Note


      • The spiral cable with sensor sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable with sensor sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.

      • As the spiral cable with sensor sub-assembly may break, do not rotate the spiral cable with sensor sub-assembly more than the specified amount.

      Tech Tips



    NG

    REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY Click here

    OK

  6. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)


    1. Disconnect the spiral cable with sensor sub-assembly connector.

    2. Disconnect the radio and display receiver assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L52-4 (EAU) - L149-23 (SWG) Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  7. CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)


    1. Disconnect the radio and display receiver assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      L146-10 (ILL+) - Body ground

      Power switch off

      Light control switch in the tail or head position

      		 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  8. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BODY GROUND)


    1. Disconnect the radio and display receiver assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L146-7 (GND1) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here