STEERING WHEEL INSTALLATION


  1. INSTALL LOWER STEERING WHEEL BOSS COVER


    1. A01JCPK

      Engage the 2 pins and 4 claws to install the lower steering wheel boss cover to the steering wheel sub-assembly.

  2. INSTALL CRUISE CONTROL SWITCH WIRE

  3. INSTALL CRUISE CONTROL MAIN SWITCH


    1. A01JB9C

      Install the cruise control main switch with the 2 screws.

    2. A01J9XU

      Connect the connector.

  4. INSTALL STEERING PAD SWITCH ASSEMBLY


    1. A01JD92

      Engage the 2 claws to install the steering pad switch assembly (RH side) to the steering wheel sub-assembly.

    2. Install the 2 screws.

      Torque:
      2.4 N*m  { 25 kgf*cm, 21 in.*lbf }
    3. A01JCKK

      Engage the 2 claws to install the steering pad switch assembly (LH side) to the steering wheel sub-assembly.

    4. Install the 2 screws.

      Torque:
      2.4 N*m  { 25 kgf*cm, 21 in.*lbf }

  5. INSTALL STEERING SHAKE DAMPER


    1. A01JAPN

      Install the steering shake damper to the steering wheel assembly with the 2 screws.

      Torque:
      2.4 N*m  { 25 kgf*cm, 21 in.*lbf }

  6. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  7. ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01JAID

      Rotate the spiral cable counterclockwise slowly by hand until it stops.

      Note

      Do not turn the spiral cable using the airbag wire harness.

    4. A01J9WYE01
      Text in Illustration
      *1 Alignment Mark

      Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

      Note

      Do not turn the spiral cable using the airbag wire harness.

      Tech Tips

      The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.

  8. INSTALL STEERING WHEEL ASSEMBLY


    1. A01JA31E01
      Text in Illustration
      *1 Matchmark

      Align the matchmarks on the steering wheel assembly and steering main shaft.

    2. Install the steering wheel assembly set nut.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

    3. Connect the connectors to the spiral cable sub-assembly.

  9. INSTALL STEERING PAD

    Tech Tips

    Refer to the instructions for Installation of the steering pad Click here.

  10. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note


    • Connect the cable to the negative (-) battery terminal with the front wheels facing straight ahead.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  12. INSTALL REAR NO. 3 FLOOR BOARD


    1. A01JC33

      Engage the 2 guides to install the rear No. 3 floor board.

  13. INSTALL REAR DECK FLOOR BOX


    1. Install the rear deck floor box.

  14. INSTALL REAR NO. 2 FLOOR BOARD


    1. A01JCWRE01

      Engage the 3 guides <A>.

    2. Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.

  15. INSPECT STEERING PAD


    1. A01JCV3

      Visually check for defects with the steering pad installed on the vehicle.


      1. The defects are as follows:


        • Cuts on the surface and in the grooves of the steering pad

        • Small cracks on the surface and in the grooves of the steering pad

        • Significant discoloration on the surface and in the grooves of the steering pad

        OK
        No defects are found.

        Tech Tips

        If any of the defects is found, replace the steering pad with a new one.

    2. Make sure that the horn sounds.

      Tech Tips

      If the horn does not sound, inspect the horn system Click here.

  16. INSPECT SRS WARNING LIGHT


    1. Inspect the SRS warning light Click here.