LIGHTING SYSTEM, Diagnostic DTC:B2417, B2418

DTC Code DTC Name
B2417 Headlight Beam Level Control Motor LH Malfunction
B2418 Headlight Beam Level Control Motor RH Malfunction

DESCRIPTION

The headlight leveling motor receives a signal from the headlight swivel ECU to operate. The headlight swivel ECU receives a signal indicating the operating conditions of the headlight leveling motor.

DTC Code DTC Detection Condition Trouble Area
B2417

Either condition is met:


  • A malfunction in the headlight leveling motor LH.

  • An open or short in the headlight leveling motor LH circuit.

  • Headlight leveling motor LH

  • Harness or connector

  • Headlight swivel ECU assembly
B2418

Either condition is met:


  • A malfunction in the headlight leveling motor RH.

  • An open or short in the headlight leveling motor RH circuit.

  • Headlight leveling motor RH

  • Harness or connector

  • Headlight swivel ECU assembly

WIRING DIAGRAM

A003BQME38

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK FOR DTC


    1. Clear the DTCs Click here.

    2. Check for DTCs Click here.

      OK
      DTC B2417 or B2418 output does not occur.

    NG

    PERFORM ACTIVE TEST USING INTELLIGENT TESTER (HEADLIGHT LEVELING MOTOR) Click here

    OK

    USE SIMULATION METHOD TO CHECK Click here

  2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (HEADLIGHT LEVELING MOTOR)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / AFS / Active Test.

    5. Using the intelligent tester, perform the Active Test.

      AFS
      Tester Display Test Part Control Range Diagnostic Note
      Drive The Leveling Motor UP Leveling motor upward operation OFF/UP -
      Drive The Leveling Motor DOWN Leveling motor downward operation OFF/DOWN -
      OK
      Headlight leveling motors operate normally.

    NG

    READ VALUE USING INTELLIGENT TESTER (HEADLIGHT SWIVEL ECU) Click here

    OK

  3. CHECK HEADLIGHT LEVELING MOTOR


    1. Temporarily replace the headlight with a new or normally functioning one Click here.

    2. Check for DTCs Click here.

      OK
      DTC B2417 or B2418 output does not occur.

    NG

    REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY Click here

    OK

    END (HEADLIGHT IS DEFECTIVE)

  4. READ VALUE USING INTELLIGENT TESTER (HEADLIGHT SWIVEL ECU)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / AFS / Data List.

    5. Using the intelligent tester, read the Data List.

      AFS
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      +B Headlight swivel ECU power source voltage/Min.: 0 V, Max.: 19.75 V 11 to 14 V -
      OK
      Power supply voltage is 11 to 14 V.

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (HEADLIGHT SWIVEL ECU - BATTERY)

    OK

  5. CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU - BODY GROUND)

    A003DIVE24
    Text in Illustration
    *1

    Front view of wire harness connector

    (to Headlight Swivel ECU)

    1. Disconnect the A38 headlight swivel ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A38-22 (E1) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU - HEADLIGHT)

    A003BCFE03
    Text in Illustration
    *1

    Front view of wire harness connector

    (to Headlight Swivel ECU)
    *2 for LH
    *3 for RH
    *4

    Front view of wire harness connector

    (to Headlight LH)
    *5

    Front view of wire harness connector

    (to Headlight RH)

    1. Disconnect the A38 headlight swivel ECU connector.

    2. Disconnect the A26 and A25 headlight connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LH
      Tester Connection Condition Specified Condition
      A38-3 (LL1+) - A26-1 (LHIG) Always Below 1 Ω
      A38-27 (LL1-) - A26-3 (LHE)
      A38-30 (LHT) - A26-2 (LHT)
      A38-3 (LL1+) - Body ground Always 10 kΩ or higher
      A38-27 (LL1-) - Body ground
      A38-30 (LHT) - Body ground
      for RH
      Tester Connection Condition Specified Condition
      A38-28 (LR1-) - A25-1 (RHE) Always Below 1 Ω
      A38-4 (LR1+) - A25-3 (RHIG)
      A38-11 (RHT) - A25-2 (RHT)
      A38-4 (LR1+) - Body ground Always 10 kΩ or higher
      A38-28 (LR1-) - Body ground
      A38-11 (RHT) - Body ground

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. CHECK HEADLIGHT LEVELING MOTOR


    1. Temporarily replace the headlight with a new or normally functioning one Click here.

    2. Check for DTCs Click here.

      OK
      DTC B2417 or B2418 output does not occur.

    NG

    REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY Click here

    OK

    END (HEADLIGHT IS DEFECTIVE)