QUARTER WINDOW GLASS (for Wagon) REMOVAL

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. REMOVE REAR BENCH TYPE SEAT CUSHION ASSEMBLY

    A003ATB

    1. Detach the 2 front hooks of the seat cushion from the vehicle body.

      Note

      Follow the instructions below carefully as the cushion frame deforms easily.


      1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

      2. Repeat for the other hook.

    2. Detach the 2 rear hooks of the seat cushion from the seatback.

      Note

      Be careful not to damage the vehicle body.

  2. REMOVE REAR SIDE SEATBACK ASSEMBLY LH

    A003CVN

    1. Remove the bolt and disconnect the rear seat 3 point type belt anchor.

    2. A003AHX

      Using a screwdriver, detach the claw to open the cap of the rear seat shoulder belt guide.

    3. Remove the seat belt from the belt guide.

    4. A003CZ2E01

      Remove the bolt, and then remove the side seatback LH as shown in the illustration.

  3. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

    A00DTSN

    1. Pull the lever and remove the tonneau cover.

  4. REMOVE ROOM PARTITION NET ASSEMBLY (w/ Partition Net)

    A00DR6R

    1. Push the 2 buttons and remove the room partition net.

  5. REMOVE LOWER DECK TRIM SIDE BOARD LH (w/ Partition Board)


    1. Remove the lower deck trim side board.

  6. REMOVE LOWER DECK TRIM SIDE BOARD RH (w/ Partition Board)


    1. Remove the lower deck trim side board.

  7. REMOVE DECK BOARD ASSEMBLY

    A00DRYP

    1. Detach the clip and 2 guides, and remove the deck board.

  8. REMOVE DECK BOARD SUB-ASSEMBLY

    A00DUX6

    1. Pull the lever and remove the deck board.

  9. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY


    1. Detach the clip and remove the No. 3 deck board.

      A00DQD8E01
  10. REMOVE REAR DECK FLOOR BOX


    1. Detach the 7 guides and remove the rear deck floor box.

      A00DPV0E01
  11. REMOVE FLOOR SIDE RAIL LH (w/ Deck Rail)

    A00DRQF

    1. Remove the 3 bolts and floor side rail.

  12. REMOVE NO. 2 DECK SIDE TRIM COVER (w/o Deck Rail)

    A00DQA9

    1. Detach the 2 clips and 3 guides, and remove the deck side trim cover.

  13. REMOVE NO. 6 DECK SIDE TRIM COVER (w/o Deck Rail)

    A00DV2F

    1. Detach the 2 claws and remove the No. 6 deck side trim cover.

  14. REMOVE ROPE HOOK ASSEMBLY (w/o Deck Rail)

    A00DPLH

    Tech Tips

    Use the same procedure for all the rope hooks.


    1. Remove the bolt and rope hook.

  15. REMOVE DECK FLOOR BOX LH

    A00DPZJ

    1. Remove the bolt.

    2. Detach the 5 guides and remove the deck floor box.

  16. REMOVE REAR FLOOR FINISH PLATE

    A00DTFU

    1. Detach the 4 clips and remove the rear floor finish plate.

  17. REMOVE FRONT DECK FLOOR BOX

    A00DT6A

    1. Remove the 2 clips.

    2. Detach the 4 guides and remove the front deck floor box.

  18. REMOVE REAR DOOR SCUFF PLATE LH

    A00DTVS

    1. Detach the 6 claws and clip, and remove the rear door scuff plate.

  19. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

    Tech Tips

    Partially remove the rear door opening trim weatherstrip LH so that the deck trim side panel can be removed Click here.

  20. REMOVE BACK DOOR WEATHERSTRIP

    Tech Tips

    Partially remove the back door weatherstrip so that the deck trim side panel can be removed Click here.

  21. REMOVE NO. 2 DECK SIDE TRIM HOOK

    A00DRD9

    Tech Tips

    Use the same procedure to remove the No. 2 deck side trim hook on the other side.


    1. Remove the screw and No. 2 deck side trim hook.

  22. REMOVE INNER ROOF SIDE GARNISH CAP LH

    A00DTOPE01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the inner roof side garnish cap.

    2. Using a screwdriver, detach the 2 claws and remove the inner roof side garnish cap.

      Tech Tips

      Tape the screwdriver tip before use.

  23. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Remove the bolt and clip.

    2. Detach the 7 clips and 3 claws.

    3. Pass the fuel lid opener cable through the panel, disconnect the connector, and then remove the deck trim side panel.

      A00DSQWE01
      Text in Illustration
      *1 Fuel Lid Opener Cable - -
  24. REMOVE INNER ROOF SIDE GARNISH LH

    A00DU8BE01
    Text in Illustration
    *1 Clip A

    1. Detach the 6 clips (do not detach clip A).

    2. Pull the inner roof side garnish in the direction indicated by the arrow in the illustration and remove it.

      Tech Tips

      Clip A remains attached to the body.

    3. Remove clip A from the vehicle body.

  25. REMOVE QUARTER WINDOW ASSEMBLY LH

    A00DQZXE01
    Text in Illustration
    *1 Protective Tape

    Tech Tips

    Apply protective tape to the outer surface of the vehicle body to prevent scratches.

    Note

    When separating the quarter window glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.


    1. Disconnect the connectors.

    2. Using a knife, cut off the moulding as shown in the illustration.

      A00DUVOE01
      Text in Illustration
      *1 Cut

      Note

      Be careful not to damage the vehicle body.

    3. A00DUTME01
      Text in Illustration
      *1 Piano Wire

      From the interior, insert a piano wire between the vehicle body and quarter window glass as shown in the illustration.

    4. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

    5. Cut through the adhesive by pulling the piano wire around the quarter window glass.

      Note

      Leave as much adhesive on the vehicle body as possible when removing the quarter window glass.

    6. Using suction cups, remove the quarter window glass.

  26. CLEAN VEHICLE BODY


    1. A00DRIHE18
      Text in Illustration
      *1 Adhesive
      *2 Vehicle Body

      Clean and shape the contact surface of the vehicle body.


      1. On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

        Note

        Be careful not to damage the vehicle body.

        Tech Tips

        Leave as much adhesive on the vehicle body as possible.

      2. Clean the contact surface of the vehicle body with cleaner.