POWER WINDOW REGULATOR MOTOR (for Rear Door) INSTALLATION

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY LH


    1. A003D64

      Apply MP grease to the sliding and rotating areas of the window regulator.

    2. A003C8ME01
      Text in Illustration
      *1 Temporary Bolt

      Loosely install the temporary bolt to the window regulator.

    3. Insert the window regulator into the door panel. Use the temporary bolt to hang the window regulator on the door panel.

      Note

      Be careful not to drop the window regulator as it may become damaged.

    4. Tighten the 4 bolts to install the rear door window regulator sub-assembly.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    5. Connect the connector.

  2. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH


    1. A005TPE

      Install the front side of the glass run.

    2. A005RMPE01

      Apply MP grease to the sliding areas of the glass channel as shown in the illustration.

      Standard
      Area Specified Condition
      A 130 mm (5.12 in.)
      B 29 mm (1.14 in.)
    3. A005UW6

      Slide the rear door glass sub-assembly as shown in the illustration to install it.

  3. INSTALL REAR DOOR QUARTER WINDOW GLASS LH


    1. A005ULKE01

      Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.

  4. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH


    1. A005VYK

      Insert the rear door window division bar sub-assembly from above.

    2. Install the rear door window division bar sub-assembly to the glass run.

    3. A005WIXE01

      Install the rear door window division bar sub-assembly with the 2 bolts and screw.

      Torque:
      6.2 N*m  { 63 kgf*cm, 55 in.*lbf, for bolt and screw }

  5. INSTALL REAR DOOR GLASS RUN LH


    1. A005U5ZE01

      Completely install the glass run.

  6. INSTALL REAR DOOR SERVICE HOLE COVER LH


    1. Apply butyl tape to the door.

    2. A005RMBE01
      Text in Illustration
      *1 Reference Point

      Pass the rear door lock remote control cable and rear door inside locking cable through a new rear door service hole cover.

      Note


      • When installing the service hole cover, pull the links and connectors through the service hole cover.

      • There should be no wrinkles or folds after attaching the service hole cover.

      • After attaching the service hole cover, check the seal quality.

    3. Attach the rear door service hole cover by using the reference points on the rear door panel.

    4. Connect the connector.

  7. INSTALL REAR DOOR FRAME GARNISH LH


    1. A005W48E01

      Attach the 2 clips to install the garnish.

  8. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH


    1. A005R46

      Install the rear door inner glass weatherstrip to the door panel.

  9. INSTALL REAR CURTAIN SUB-ASSEMBLY LH (w/ Rear Door Sunshade)


    1. Install the clip to the rear curtain sub-assembly.

    2. A005RW1

      Attach the 2 claws to install the rear curtain sub-assembly to the door trim board.

    3. Install the 6 screws.

  10. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A005UJO

      Connect the 2 cables to the inside handle.

    2. for 11 Speakers:

      Connect the connector.

    3. A005REME01
      Text in Illustration
      *1 w/ Rear Door Sunshade
      *2 w/o Rear Door Sunshade

      Attach the rear door trim board with the 4 claws on the rear door inner glass weatherstrip.

    4. A005VW3

      Install the rear door trim board with the 8 clips.

    5. Install the 3 screws.

  11. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. Connect the connector.

    2. A005UGK

      Attach the 6 claws and clip to install the rear power window regulator switch assembly with rear door armrest base panel.

  12. INSTALL DOOR ASSIST GRIP COVER LH


    1. A005SDM

      Attach the 10 claws to install the door assist grip cover.

  13. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH


    1. A005SGF

      Attach the 3 claws to install the rear door inside handle bezel plug.

  14. INSTALL REAR DOOR NO. 1 STIFFENER CUSHION


    1. A005VX9

      Install the rear door No. 1 stiffener cushion.

  15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.