POWER WINDOW REGULATOR MOTOR (for Rear Door) REMOVAL

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR DOOR NO. 1 STIFFENER CUSHION


    1. A010J61

      Remove the stiffener cushion.

  4. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH


    1. A010HOS

      Using moulding remover A, detach the 3 claws and remove the bezel plug.

  5. REMOVE DOOR ASSIST GRIP COVER LH


    1. A010HM7

      Using moulding remover A, detach the 10 claws and remove the assist grip cover.

  6. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. A010K1N

      Using moulding remover A, detach the 6 claws and the clip.

    2. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.

  7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A010K0H

      Remove the 3 screws.

    2. Using a clip remover, detach the 8 clips.

    3. A010J2PE01
      Text in Illustration
      *1 w/ Rear Door Sunshade
      *2 w/o Rear Door Sunshade

      Pull out the rear door trim board in the direction indicated by the arrow.

    4. for 11 Speakers:


      1. Disconnect the connector.

    5. A010HB4

      Disconnect the 2 cables from the inside handle.

  8. REMOVE REAR CURTAIN SUB-ASSEMBLY LH (w/ Rear Door Sunshade)


    1. A010M56

      Remove the 6 screws, detach the 2 claws and remove the curtain.

    2. Remove the clip from the rear curtain sub-assembly.

  9. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH


    1. A010HQX

      Remove the inner glass weatherstrip by pulling it upward in the direction indicated by the arrow in the illustration.

  10. REMOVE REAR DOOR FRAME GARNISH LH


    1. A010IF9E01

      Detach the 2 clips.

    2. Detach the claws and remove the rear door frame garnish.

  11. REMOVE REAR DOOR SERVICE HOLE COVER LH


    1. A010I2V

      Disconnect connector and remove the service hole cover.

      Tech Tips

      Remove the remaining tape on the door.

  12. REMOVE REAR DOOR GLASS RUN LH


    1. A010JRGE01

      Remove the rear door glass run.

  13. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH


    1. A010J8PE01

      Remove the screw.

    2. Remove the 2 bolts and rear door window division bar sub-assembly.

  14. REMOVE REAR DOOR QUARTER WINDOW GLASS LH


    1. A010LE3E01

      Remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit as shown in the illustration.

  15. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH


    1. A010GQV

      Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

      Note

      Do not damage the door glass.

  16. REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY LH


    1. A00OJR8E01
      Text in Illustration
      *1 Temporary Bolt

      Disconnect the connector.

    2. Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall and cause damage.

    3. Remove the 3 bolts.

    4. Remove the rear door window regulator assembly.

    5. Remove the temporary bolt from the rear door window regulator.