LOWER INSTRUMENT PANEL INSTALLATION

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. Attach the claw to install the instrument panel.

    2. Attach the 10 clamps.

    3. Install the 2 bolts.

      A00OKGW

    4. Install the screw.

    5. Install the screw <D>.

    6. Install the 2 bolts <B> and 8 screws <C>.

      A00OK7AE01
      Text in Illustration
      *1 Bolt <B> *3 Screw <D>
      *2 Screw <C> - -
    7. A00OL5C

      When replacing the lower instrument panel sub-assembly with a new one:


      1. Twist the ribs (the pieces used to maintain the shape of the panel) in the direction of the arrow in the illustration until it detaches from the instrument panel, and remove the rib.

  2. INSTALL COOLER (ROOM TEMPERATURE SENSOR) THERMISTOR (for Automatic Air Conditioning System)


    1. A00OMO1

      Attach the 2 claws to install the thermistor.

    2. Connect the connector and aspirator hose.

  3. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. A00OJGA

      Connect the hood lock control cable assembly.

    2. Attach the 3 claws to install the hood lock control lever sub-assembly.

  4. INSTALL FUEL LID OPENER SWITCH


    1. A003CI3

      Attach the 2 claws to install the fuel lid opener switch.

    2. Connect the connector.

  5. INSTALL VSC OFF SWITCH (w/ VSC)


    1. A003CSZ

      Attach the 2 claws to install the VSC OFF switch to the lower instrument panel.

    2. Connect the VSC OFF switch connector.

  6. INSTALL HEADLIGHT SWIVEL MAIN SWITCH (w/ AFS)


    1. A003BUE

      Connect the connector.

    2. Attach the 2 claws to install the switch.

  7. INSTALL CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System)


    1. A00OK11

      Install the ECU with the bolt.

    2. A00OI45

      Connect the connector.

  8. INSTALL ENGINE SWITCH (for LHD with Entry and Start System)


    1. A00OJAQ

      Connect the connector.

    2. Attach the 2 claws to install the switch.

  9. INSTALL ELECTRIC PARKING BRAKE SWITCH ASSEMBLY


    1. Connect the connector.

    2. A010L4JE01

      Install the electric parking brake switch with the 3 bolts.

      Torque:
      7.1 N*m  { 72 kgf*cm, 62 in.*lbf }

  10. INSTALL GLOVE BOX LIGHT ASSEMBLY


    1. A003EC3

      Connect the connector.

    2. Attach the 2 claws to install the glove box light.

  11. INSTALL COWL SIDE TRIM BOARD LH

    A010L6A

    1. Attach the clip, claw and guide to install the cowl side trim board.

  12. INSTALL COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure described for the LH side.

  13. INSTALL FRONT DOOR SCUFF PLATE LH

    A010K3R

    1. Attach the 2 clips and 8 claws to install the front door scuff plate.

  14. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  15. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A00OIAH

      Attach the guide.

    2. Connect the connector.

    3. A00OIVV

      Attach the 3 claws to install the under cover.

  16. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY


    1. A00OIZC

      Connect the connector.

      Note

      When handling the airbag connector, take care not to damage the airbag wire harness.

    2. Attach the 2 claws to install the DLC3.

    3. Attach the 7 claws to install the instrument panel airbag.

    4. Install the 4 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  17. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A00ONIX

      Attach the guide.

    2. Connect the connectors.

    3. A00OMHS

      Attach the claw to install the under cover.

    4. Install the 2 screws <A>.

  18. INSTALL COIN BOX ASSEMBLY


    1. A00OL9A

      Attach the 2 hinges to install the coin box.

    2. A00OM1K

      While pushing in the sides of the coin box as indicated by the arrows in the illustration, close the coin box to engage the 2 stoppers.

  19. INSTALL NO. 1 SWITCH HOLE BASE (for RHD)


    1. Connect the connectors.

    2. Attach the 3 claws and 4 clips to install the switch hole base.

      A00OM2SE01

  20. INSTALL NO. 1 SWITCH HOLE BASE (for LHD)


    1. A00ONHE

      Connect the connectors.

    2. Attach the 2 claws and 4 clips to install the switch hole base.

  21. INSTALL AIR CONDITIONING CONTROL ASSEMBLY

    A010H0H

    1. Connect the connector.

    2. Attach the 4 clips to install the air conditioning control.

  22. INSTALL CONSOLE BOX ASSEMBLY


    1. for Manual Transaxle:


      1. Install the console box with the 2 screws.

    2. for Automatic Transaxle and CVT:


      1. Install the console box with the 4 screws.

    3. Connect the connectors.

    4. Install the 4 bolts.

      A010I1ZE05

  23. INSTALL CONSOLE BOX CARPET


    1. Install the 2 carpets.

  24. INSTALL REAR CONSOLE BOX CUP HOLDER


    1. Install the cup holder.

  25. INSTALL LOWER INSTRUMENT CLUSTER FINISH PANEL


    1. A010JZLE01
      Text in Illustration
      *1 w/ Seat Heater System

      Connect the connectors.

    2. A010L90

      Attach the 2 clips to install the finish panel.

  26. INSTALL REAR UPPER CONSOLE PANEL SUB-ASSEMBLY (for Automatic Transaxle and CVT)


    1. A010JH2

      Connect the connector.

    2. Attach the 2 claws and 6 clips to install the console panel.

  27. INSTALL REAR UPPER CONSOLE PANEL SUB-ASSEMBLY (for Manual Transaxle)


    1. A010K71

      Attach the 2 claws and 6 clips to install the console panel.

    2. A010KDA

      Attach the cover to the shaft.

  28. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle and CVT)


    1. A010LKB

      Install the shift lever knob and twist it in the direction indicated by the arrow.

  29. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)


    1. A010LOW

      Install the shift lever knob and twist it in the direction indicated by the arrow.

  30. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Audio)


    1. for Radio Receiver Type:

      Install the radio receiver assembly Click here.

    2. for Radio and Display Type:

      Install the radio receiver assembly Click here.

  31. INSTALL STEREO OPENING COVER WITH BRACKET (w/o Audio)


    1. A00OJ3H

      Install the opening cover with bracket with the 4 screws.

  32. INSTALL COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


    1. A00OIBEE01
      Text in Illustration
      *1 Clamp
      *2 Claw

      Using pliers, pinch the clamp and attach the claw to install the combination switch assembly with spiral cable sub-assembly to the steering column assembly.

    2. Connect the connectors to the combination switch assembly with spiral cable sub-assembly.

  33. INSTALL TILT AND TELESCOPIC SWITCH (for Power Tilt and Power Telescopic Steering Column)

    A006WII

    1. Attach the claw to install the switch.

    2. Connect the switch connector.

  34. INSTALL UPPER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)

    Note

    If the steering column cover is installed in an incorrect order, it will not be possible to assemble the steering column cover.


    1. A00ONF4

      Attach the claw and 2 pins to install the upper steering column cover.

  35. INSTALL LOWER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)

    Note

    If the steering column cover is installed in an incorrect order, it will not be possible to assemble the steering column cover.


    1. A00OIED

      Attach the 2 claws to install the lower steering column cover.

    2. A00ONL0

      Attach the 4 claws.

    3. A00OK2Y

      Attach the claw.

      Tech Tips

      Press the area around the claw to attach it.

  36. INSTALL LOWER NO. 2 STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)

    A00OMND

    1. Attach the 4 claws to install the lower No. 2 steering column cover.

  37. INSTALL UPPER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)

    Note

    If the steering column cover is installed in an incorrect order, it will not be possible to assemble the steering column cover.


    1. A00OIUR

      Attach the claw and 2 pins to install the upper steering column cover.

  38. INSTALL LOWER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)

    Note

    If the steering column cover is installed in an incorrect order, it will not be possible to assemble the steering column cover.


    1. A00OMMR

      Attach the 2 claws to install the lower steering column cover.

    2. A00OL3D

      Attach the 4 claws.

    3. A00OK2L

      Attach the claw.

      Tech Tips

      Press the area around the claw to attach it.

  39. INSTALL STEERING WHEEL ASSEMBLY


    1. Install the steering wheel assembly Click here.

  40. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY


    1. Install the upper instrument panel sub-assembly Click here.

  41. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  42. RESTORE AUTOAWAY/RETURN FUNCTION (for Power Tilt and Power Telescopic Steering Column)


    1. Restore the Autoaway/Return function setting to the previous condition by changing the customize parameter Click here.

  43. CHECK SRS WARNING LIGHT


    1. Check the SRS warning light Click here.