REAR SEAT OUTER BELT ASSEMBLY (for Wagon) INSTALLATION

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL OUTER BELT ANCHOR BRACKET SUB-ASSEMBLY LH

    A005T3N

    1. Align the claw with the anchor bracket positioning hole and install the anchor bracket with the 2 bolts.

      Torque:
      41 N*m  { 418 kgf*cm, 30 ft.*lbf }

  2. INSTALL REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH

    A005TCG

    1. Align the claw with the 3 point type belt positioning guide and install the 3 point type belt with the nut.

      Torque:
      41 N*m  { 418 kgf*cm, 30 ft.*lbf }

  3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Pass the fuel lid opener cable through the deck trim side panel.

    2. Connect the connector.

    3. Detach the 7 clips and 3 claws to install the deck trim side panel.

    4. Install the bolt and clip.

      A00DSQWE01
      Text in Illustration
      *1 Fuel Lid Opener Cable - -

  4. INSTALL INNER ROOF SIDE GARNISH CAP LH

    A00DUDF

    1. Attach the 2 claws to install the inner roof side garnish cap.

  5. INSTALL NO. 2 DECK SIDE TRIM HOOK

    A00DRD9

    Tech Tips

    Use the same procedure to install the No. 2 deck side trim hook on the other side.


    1. Install the No. 2 deck side trim hook with the screw.

  6. INSTALL BACK DOOR WEATHERSTRIP

    A00DU53

    1. Align the center mark of the back door weatherstrip with the position indicated by the arrow in the illustration and install the back door weatherstrip.

  7. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

    A00DQUFE01
    Text in Illustration
    *1 Paint Mark
    *2 Mark Position

    1. Install the rear door opening trim weatherstrip as shown in the illustration.

  8. INSTALL REAR DOOR SCUFF PLATE LH

    A00DTVS

    1. Attach the clip and 6 claws to install the front door scuff plate.

  9. INSTALL REAR FLOOR FINISH PLATE

    A00DTFU

    1. Attach the 4 clips to install the rear floor finish plate.

  10. INSTALL DECK FLOOR BOX LH

    A00DUZL

    1. Attach the 5 guides to install the deck floor box.

  11. INSTALL ROPE HOOK ASSEMBLY (w/o Deck Rail)

    A00DPLH

    Tech Tips

    Use the same procedure for all the rope hooks.


    1. Install the rope hook with the bolt.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  12. INSTALL NO. 6 DECK SIDE TRIM COVER (w/o Deck Rail)

    A00DV2F

    1. Attach the 2 claws to install the No. 6 deck side trim cover.

  13. INSTALL NO. 2 DECK SIDE TRIM COVER (w/o Deck Rail)

    A00DQA9

    1. Attach the 2 clips and 3 guides to install the No. 2 deck side trim cover.

  14. INSTALL FLOOR SIDE RAIL LH (w/ Deck Rail)

    A00DRQF

    1. Install the floor side rail with the 3 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  15. INSTALL REAR DECK FLOOR BOX


    1. Attach the 7 guides to install the rear deck floor box.

      A00DPV0E01
    2. A00DT3R

      Install the bolt.

    3. A00DRKM

      Install the bolt.

  16. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY


    1. Attach the clip to install the No. 3 deck board.

      A00DQD8E01

  17. INSTALL DECK BOARD SUB-ASSEMBLY

    A00DUX6

    1. Pull the lever to install the deck board.

  18. INSTALL DECK BOARD ASSEMBLY

    A00DRYP

    1. Attach the clip and 2 guides to install the deck board.

  19. INSTALL LOWER DECK TRIM SIDE BOARD LH (w/ Partition Board)


    1. Install the lower deck trim side board.

  20. INSTALL ROOM PARTITION NET ASSEMBLY (w/ Partition Net)

    A00DR1G

    1. Install the room partition net.

  21. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

    A00DTSN

    1. Pull the lever to install the tonneau cover.

  22. INSTALL REAR SIDE SEATBACK ASSEMBLY LH

    A005R52

    1. Install the claw as shown in the illustration.

    2. Install the side seatback with the bolt.

      Torque:
      7.8 N*m  { 80 kgf*cm, 69 in.*lbf }
    3. A005TMWE01
      Text in Illustration
      *1 Protruding Part

      Install the rear seat 3 point type belt anchor with the bolt.

      Torque:
      41 N*m  { 418 kgf*cm, 30 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat 3 point type belt to overlap the protruding parts of the floor panel.

    4. Install the seat belt to the belt guide.

    5. Attach the claw to close the cap of the rear seat shoulder belt guide.

    6. Check if the ELR locks.

      Note

      The check should be performed with the outer belt assembly installed.


      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

  23. INSTALL REAR BENCH TYPE SEAT CUSHION ASSEMBLY

    A003CGQ

    1. Attach the 2 rear hooks of the seat cushion to the seatback.

    2. Attach the 2 front hooks to install the seat cushion.

    3. Confirm that the seat cushion is firmly installed.

      Note

      When installing the seat cushion, make sure the seat belt buckle is not under the seat cushion.