FRONT SEAT CUSHION HEATER (for Power Seat) INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH

    Note

    When replacing either the front seat cushion heater assembly or separate type front seat cushion pad due to a malfunction, be sure to replace both of them with new parts.


    1. Remove the peeling paper from a new front seat cushion heater assembly LH.

    2. A00OLW4

      Install the front seat cushion heater assembly LH to a new separate type front seat cushion pad.

  2. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. A00OKGP

      Attach the hooks to install the separate type front seat cushion cover to the separate type front seat cushion pad.

      Note


      • Be careful not to damage the cover.

      • When attaching the hooks, avoid wrinkling the cover.

  3. INSTALL SEAT CUSHION COVER WITH PAD


    1. Attach the hooks to install the seat cushion cover with pad.

      A00OKFL

    2. Connect the 2 connectors.

    3. A00OKBS

      for Driver Side:

      Attach the wire harness clamp.

    4. A00OLIT

      for Front Passenger Side:

      Attach the 2 hooks to connect the connector holder.

    5. A00ONI3

      Install a new cable tie.

    6. A00OI8F

      Connect the connector.

  4. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH


    1. A005REIE01
      Text in Illustration
      *1 Protruding Part

      Install the front seat inner belt with the nut.

      Torque:
      41 N*m  { 418 kgf*cm, 30 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

    2. for Driver Side:

      Connect the connector and attach the clamps.

    3. for Passenger Side:

      Connect the connectors and attach the clamps.

  5. INSTALL FRONT SEAT INNER CUSHION SHIELD LH


    1. A00ON87E01
      Text in Illustration
      *1 Hook
      *2 Wire Harness Clamp

      Attach the wire harness clamp and hook to install the front seat inner cushion shield LH.

    2. Install the 2 screws.

  6. INSTALL FRONT POWER SEAT SWITCH


    1. A00OM6W

      Install the front power seat switch with the 3 screws.

    2. Connect the connector.

  7. INSTALL FRONT SEAT CUSHION SHIELD LH WITH FRONT SEAT INNER NO. 1 CUSHION SHIELD


    1. A00OMVA

      for Driver Side:

      Connect the connector.

    2. A00OJR5

      Attach the hook to install the front seat cushion shield LH with front seat inner No. 1 cushion shield.

    3. Install the 2 screws.

    4. A00ONUD

      Attach the 2 claws and install the 2 screws.

    5. A00OI4P

      Attach the 2 rubber bands.

  8. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. A00OIGD

      Attach the 4 claws to install the slide and vertical power seat switch knob.

  9. INSTALL RECLINING POWER SEAT SWITCH KNOB


    1. A00OJR9

      Attach the 2 claws to install the reclining power seat switch knob.

  10. INSTALL FRONT SEAT ASSEMBLY

    Click here

  11. CHECK SRS WARNING LIGHT

    Click here

  12. INSPECT FRONT SEAT ASSEMBLY


    1. Check the power seat operation Click here.

    2. Check the seat heater operation.


      1. Turn the ignition switch to ON.

      2. Operate the seat heater switch on.

      3. Wait 5 minutes or more and confirm that the seat surface becomes warm.