FRONT SEATBACK HEATER (for Manual Seat) INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. INSTALL FRONT SEATBACK HEATER ASSEMBLY

    Note

    When replacing either the front seatback heater assembly or separate type front seatback pad due to a malfunction, be sure to replace both of them with new parts.


    1. Remove the peeling paper from a new front seatback heater assembly.

    2. A00OHYV

      Install the front seatback heater assembly to a new separate type front seatback pad.

  2. INSTALL SEPARATE TYPE FRONT SEATBACK PAD


    1. A00OMMP

      Install the separate type front seatback pad.

    2. A00OKVM

      Connect the connector.

  3. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    1. A00ONM4

      Attach the 2 hooks.

    2. A00OMKO

      Attach the 2 claws to install the 2 front seat headrest supports.

    3. w/ Active Headrest:


      1. A00OJU0

        Install the front seat headrest assembly.

        Note

        Push in the front seat headrest assembly until the headrest lock engages.

      2. A00ONJ0

        Pass the cable through the hole of the seatback frame.

      3. A00OJDI

        Attach the 2 claws to install the clip.

      4. A00OIX4E01
        Text in Illustration
        *1 Cable End

        Pull the cable through the clip until the cable end reaches the clip.

      5. A00OI4E

        Install a new cable tie.

      6. A00OKGKE01
        Text in Illustration
        *1 Hook
        *2 Hog Ring
        *3 Hog Ring Pliers

        Attach the 2 hooks to close the seatback mat.

      7. Using hog ring pliers, install a new hog ring.

      8. A00OLW6

        Attach the 2 claws to connect the cable to the active headrest lower unit.

      9. A00OJ98

        Attach the 2 claws to install the active headrest lower unit.

      10. A00OMWJE01
        Text in Illustration
        *1 Cable End
        A00OJPS Pull

        Pull the cable and connect the cable end to the active headrest lower unit.

      11. A00OIBR

        Attach the 7 hooks to install the actuator shield.

    4. A00OL1YE02
      Text in Illustration
      *1 Hook
      *2 Hog Ring
      *3 Hog Ring Pliers

      Attach the 3 hooks.

    5. Using hog ring pliers, install the upper part of the separate type front seatback cover to the separate type front seatback pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    6. A00OIU0E01
      Text in Illustration
      *1 Seatback Cover Bracket

      Attach the seatback cover bracket with the screw.

      Note

      After the separate type front seatback cover is installed, make sure the seatback cover bracket is not twisted.

    7. A00OIFV

      Pass the 2 straps through the 2 holes of the separate type front seatback pad to the backside.

    8. A00OMX4

      Attach the 2 hooks to connect the 2 straps.

    9. A00OILD

      Attach the 2 hooks at the bottom of the separate type front seatback cover.

    10. Attach the 2 hooks.

      A00OM3Y
    11. A00ON1Q

      w/o Active Headrest:

      Install the front seat headrest assembly.

      Note

      Push in the front seat headrest assembly until the headrest lock engages.

  4. INSTALL FRONT SEAT INNER CUSHION SHIELD LH


    1. A00ON87E01
      Text in Illustration
      *1 Hook
      *2 Wire Harness Clamp

      Attach the wire harness clamp and hook to install the front seat inner cushion shield LH.

    2. Install the 2 screws.

  5. INSTALL FRONT SEAT CUSHION SHIELD LH


    1. A00OIA6

      w/ Lumbar Support:

      Connect the connector.

    2. A00OJGH

      Attach the claw and hook to install the front seat cushion shield LH.

    3. Install the 2 screws.

    4. A00OJNF

      Attach the 2 rubber bands.

  6. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH


    1. A00OMSX

      Attach the claw to install the reclining adjuster release handle LH.

  7. INSTALL VERTICAL ADJUSTING HANDLE LH (for Driver Side)


    1. A00OMVH

      Install the vertical adjusting handle LH with the 2 screws.

  8. INSTALL VERTICAL SEAT ADJUSTER KNOB CAP (for Driver Side)


    1. A00OM9G

      Attach the 3 claws to install the vertical seat adjuster knob cap.

  9. INSTALL FRONT SEAT ASSEMBLY

    Click here

  10. CHECK SRS WARNING LIGHT

    Click here

  11. INSPECT FRONT SEAT ASSEMBLY


    1. Check the seat heater operation.


      1. Turn the ignition switch to ON.

      2. Operate the seat heater switch on.

      3. Wait 5 minutes or more and confirm that the seat surface becomes warm.

    2. w/ Lumbar Support:

      Check the lumbar support operation.


      1. Operate the lumbar front power seat switch and check that the lumbar support moves in both directions.