SEAT HEATER SWITCH INSTALLATION

Tech Tips


  • Use the same procedure for LHD and RHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. INSTALL SEAT HEATER SWITCH (for RH Side)


    1. A010G8S

      Attach the 2 claws to install the switch.

  2. INSTALL SEAT HEATER SWITCH (for LH Side)


    1. A010ISC

      Attach the 2 claws to install the switch.

  3. INSTALL LOWER INSTRUMENT CLUSTER FINISH PANEL


    1. A010JZLE01
      Text in Illustration
      *1 w/ Seat Heater System

      Connect the connectors.

    2. A010L90

      Attach the 2 clips to install the finish panel.

  4. INSTALL REAR UPPER CONSOLE PANEL SUB-ASSEMBLY (for Manual Transaxle)


    1. A010K71

      Attach the 2 claws and 6 clips to install the console panel.

    2. A010KDA

      Attach the cover to the shaft.

  5. INSTALL REAR UPPER CONSOLE PANEL SUB-ASSEMBLY (for Automatic Transaxle and CVT)


    1. A010JH2

      Connect the connector.

    2. Attach the 2 claws and 6 clips to install the console panel.

  6. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)


    1. A010LOW

      Install the shift lever knob and twist it in the direction indicated by the arrow.

  7. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle and CVT)


    1. A010LKB

      Install the shift lever knob and twist it in the direction indicated by the arrow.

  8. INSTALL INSTRUMENT PANEL FINISH PANEL END RH (for LHD)


    1. A00OM2F

      Attach the 4 clips and 5 claws to install the panel end.

  9. INSTALL INSTRUMENT PANEL FINISH PANEL END RH (for RHD)


    1. w/o TOYOTA Parking Assist-sensor System:


      1. Attach the 4 clips and 5 claws to install the panel end.

    2. w/ TOYOTA Parking Assist-sensor System:


      1. Connect the connector.

      2. Attach the 4 clips and 5 claws to install the panel end.

        A00OI5CE01

  10. INSTALL INSTRUMENT PANEL FINISH PANEL END LH


    1. Attach the 4 clips and 5 claws to install the panel end.

      A00OME5E01

  11. INSTALL NO. 3 BOX PANEL (w/ Console Box Lid)


    1. When replacing the No. 3 box panel with a new one:


      1. A010LS3E01
        Text in Illustration
        *1 Cut

        Cut off the rib (the piece used to maintain the shape of the panel) shown in the illustration.

    2. Attach the 6 clips to install the box panel.

      A010HDEE01

  12. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. A00OJ4PE01
      Text in Illustration
      *1 Guide
      *2 Clamp

      Attach the guide near the front of the vehicle.

    2. Attach the clamp.

    3. Attach the 2 clips and 5 claws to install the finish panel.

  13. INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL


    1. A00OMUOE01
      Text in Illustration
      *1 Guide
      *2 Clamp

      Attach the guide near the front of the vehicle.

    2. Attach the clamp.

    3. Attach the 2 clips and 5 claws to install the finish panel.

  14. INSPECT FRONT SEAT ASSEMBLY


    1. Check the seat heater operation.


      1. Turn the ignition switch to ON.

      2. Operate the seat heater switch on.

      3. Wait 5 minutes or more and confirm that the seat surface becomes warm.