LUMBAR SUPPORT ADJUSTER ASSEMBLY (for Manual Seat) REMOVAL

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. REMOVE FRONT SEAT ASSEMBLY

    Click here

  2. REMOVE VERTICAL SEAT ADJUSTER KNOB CAP


    1. A00OK7DE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 3 claws and remove the vertical seat adjuster knob cap.

      Tech Tips

      Tape the screwdriver tip before use.

  3. REMOVE VERTICAL ADJUSTING HANDLE LH


    1. A00OMVH

      Remove the 2 screws and vertical adjusting handle LH.

  4. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH


    1. A00OLYNE01
      Text in Illustration
      *1 Protective Tape

      Raise the reclining adjuster release handle LH to reveal the claw. Using a screwdriver, detach the claw and remove the reclining adjuster release handle LH.

      Tech Tips

      Tape the screwdriver tip before use.

  5. REMOVE FRONT SEAT CUSHION SHIELD LH


    1. A00OHW8

      Detach the 2 rubber bands.

    2. A00ONR0

      Remove the 2 screws.

    3. Detach the hook and claw and remove the front seat cushion shield LH.

    4. A00OIA6

      w/ Lumbar Support:

      Disconnect the connector.

  6. REMOVE FRONT SEAT INNER CUSHION SHIELD LH


    1. A00OMPQE01
      Text in Illustration
      *1 Hook
      *2 Wire Harness Clamp

      Remove the 2 screws.

    2. Detach the hook and wire harness clamp and remove the front seat inner cushion shield LH.

  7. REMOVE SEPARATE TYPE FRONT SEATBACK COVER


    1. A00OJ55E01
      Text in Illustration
      *1 Protective Tape

      w/o Active Headrest:

      Using a screwdriver, push the headrest support lock to release the lock and remove the front seat headrest assembly.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Detach the 2 hooks.

      A00ONQ1
    3. A00OILD

      Detach the 2 hooks from the bottom of the separate type front seatback cover.

    4. A00OM19

      Detach the 2 hooks and disconnect the 2 straps.

    5. A00ONU5

      Pass the 2 straps through the 2 holes of the separate type front seatback pad to the surface.

    6. A00OIU0E01
      Text in Illustration
      *1 Seatback Cover Bracket

      Remove the screw and detach the seatback cover bracket.

    7. A00OME0E01
      Text in Illustration
      *1 Hook
      *2 Hog Ring

      Remove the hog rings and detach the 3 hooks from the center of the separate type front seatback pad.

    8. w/ Active headrest:


      1. A00OIBR

        Detach the 7 hooks and remove the actuator shield.

      2. A00ONV8E01
        Text in Illustration
        *1 Cable End
        A00OMA6 Pull

        Pull the cable to loosen it, and then disconnect the cable end from the active headrest lower unit.

      3. A00OJIH

        Detach the 2 claws and remove the active headrest lower unit.

      4. A00OLW6

        Using a screwdriver, detach the 2 claws and disconnect the cable.

      5. A00OKVCE01
        Text in Illustration
        *1 Hook
        *2 Hog Ring

        Remove the hog ring and detach the 2 hooks and open the seatback mat.

      6. A00OI4E

        Cut off the cable tie.

      7. A00OKRGE01
        Text in Illustration
        *1 Cable End

        Push the cable to push out the cable end from the clip.

      8. A00OJDI

        Detach the 2 claws and remove the clip.

      9. A00OHQJ

        Pull the cable through the hole of the seatback frame.

      10. A00OMD2E01
        Text in Illustration
        *1 Protective Tape

        Using a screwdriver, push the headrest support lock to release the lock and remove the front seat headrest assembly.

        Tech Tips

        Tape the screwdriver tip before use.

    9. A00OIA8

      Detach the 2 claws and remove the 2 front seat headrest supports.

    10. A00ONM4

      Detach the 2 hooks and remove the separate type front seatback cover.

  8. REMOVE SEPARATE TYPE FRONT SEATBACK PAD


    1. A00OKVM

      w/ Seat Heater System:

      Disconnect the connector.

    2. A00OJNW

      Remove the separate type front seatback pad.

  9. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH


    1. A00ON1B

      Disconnect the connector.

    2. A00OLVO

      Detach the 8 hooks and remove the seatback spring.

    3. A00ONFCE01
      Text in Illustration
      *1 Back Sheet

      Pull the wire harness and disconnect it from the 2 back sheets as shown in the illustration.

    4. A00OIAPE01
      Text in Illustration
      *1 Back Sheet
      *2 Hook A
      *3 Hook B
      *4 Cable Tie

      Detach the 4 hooks A and fold back the 2 back sheets.

    5. Cut off the 2 cable ties, detach the 2 hooks B, and then remove the lumbar support adjuster assembly LH from the seatback spring.