FRONT POWER SEAT MOTOR ASSEMBLY (for Rear Lifter) INSTALLATION

Note

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. INSTALL POWER SEAT MOTOR ASSEMBLY (for Rear Lifter)


    1. Install a nose piece to an air riveter or hand riveter. Then insert the mandrel part of a new φ4 mm rivet into the nose piece.

    2. A00DUMOE01
      Text in Illustration
      *1 Air Riveter

      Using the air riveter or hand riveter, install the motor with a new rivet.

      Tech Tips

      If the rivet cannot be cut, pull it once and cut it.

      Note


      • A00DQBVE02

        Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

      • A00DU0FE02

        Confirm that the rivet is seated properly against the motor.

      • Do not tilt the riveter when installing the rivet to the motor.

      • Do not leave any space between the rivet head and motor.

      • A00DQ65E02

        Do not leave any space between the motor and seat adjuster. Firmly hold together the 2 items while installing the rivet.

    3. A00DUMAE01
      Text in Illustration
      *1 Air Riveter

      Using the air riveter or hand riveter, install 2 new rivets.

      Tech Tips

      If the rivet cannot be cut, pull it once and cut it.

      Note


      • A00DQBVE02

        Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

      • A00DU0FE02

        Confirm that the rivets are seated properly against the seat adjuster.

      • Do not tilt the riveter when installing the rivet to the seat adjuster.

      • Do not leave any space between the rivet head and seat adjuster.

      • A00DQ65E02

        Do not leave any space between the seat adjuster and motor. Firmly hold together the 2 items while installing the rivet.

  2. INSTALL SEAT CUSHION COVER WITH PAD


    1. Attach the hooks to install the seat cushion cover with pad.

      A010LCG

    2. Connect the connectors.

    3. A010MAE

      for Driver Side:

      Attach the wire harness clamp.

    4. for Passenger Side:


      1. A010LZM

        Attach the 2 hooks to install the connector holder.

    5. A010KJ1

      Install a new cable tie.

    6. A010IVJ

      Connect the connector.

    7. A010GND

      Attach the 2 rubber bands.

  3. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH


    1. A005REIE01
      Text in Illustration
      *1 Protruding Part

      Install the front seat inner belt with the nut.

      Torque:
      41 N*m  { 418 kgf*cm, 30 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

    2. for Driver Side:

      Connect the connector and attach the clamps.

    3. for Passenger Side:

      Connect the connectors and attach the clamps.

  4. INSTALL FRONT SEAT INNER CUSHION SHIELD LH


    1. A010FYQE01
      Text in Illustration
      *1 Hook
      *2 Wire Harness Clamp

      Attach the wire harness clamp.

    2. Attach the hook to install the cushion shield.

    3. Install the 2 screws.

  5. INSTALL FRONT POWER SEAT SWITCH


    1. A00DS2M

      Connect the connector.

    2. Install the switch with the 3 screws.

  6. INSTALL FRONT SEAT CUSHION SHIELD LH WITH FRONT SEAT INNER NO. 1 CUSHION SHIELD


    1. A010H4B

      for Driver Side:

      Connect the connector.

    2. A010L01

      Attach the hook to install the front seat cushion shield LH with front seat inner No. 1 cushion shield.

    3. Install the 2 screws.

    4. A010KW3

      Attach the 2 claws and install the 2 screws.

  7. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. A010LMY

      Attach the 4 claws to install the knob.

  8. INSTALL RECLINING POWER SEAT SWITCH KNOB


    1. A010M69

      Attach the 2 claws to install the knob.

  9. INSTALL FRONT SEAT ASSEMBLY


    1. Install the front seat assembly Click here.

  10. CHECK SRS WARNING LIGHT


    1. Check the SRS warning light Click here.

  11. INSPECT FRONT SEAT ASSEMBLY


    1. Check the front seat assembly Click here.

    2. Check the seat heater operation.


      1. Turn the ignition switch to ON.

      2. Operate the seat heater switch ON.

      3. Wait 5 minutes or more and confirm that the seat surface becomes warm.