FRONT POWER SEAT MOTOR ASSEMBLY (for Reclining) INSTALLATION

Note

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for the LH side and RH side.

  • The procedure listed below is for the LH side.


  1. INSTALL POWER SEAT MOTOR ASSEMBLY (for Reclining)


    1. A003BS9

      Remove the 2 holders together with the 2 inner reclining rods.

    2. A003C2M

      Remove the inner reclining rod and push nut.

    3. A003CBJ

      Remove the inner reclining rod and push nut.

    4. A003E0Y

      Install the 2 holders.

    5. A003BHA

      Install the push nut.

      Note

      Make sure the direction of the push nut is as shown in the illustration.

    6. A003CEZ

      Install the push nut.

      Note

      Make sure the direction of the push nut is as shown in the illustration.

    7. A003AUK

      Temporarily install the power seat motor with the bolt.

    8. A003AWK

      Temporarily install the inner reclining rod.

    9. A003C1V

      Temporarily install the inner reclining rod.

    10. A003DSF

      Push in the 2 inner reclining rods in alternating passes to install them

      Note

      Make sure that the holder does not interfere with the motor or front seatback assembly.

    11. Using a 5 mm socket hexagon wrench, tighten the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }
    12. A003DRF

      Attach the 8 hooks to install the seatback spring.

    13. A003C2L

      for Driver Side:

      Connect the connectors.

    14. A003BPC

      for Passenger Side:

      Connect the connector.

    15. A003DVB

      Install the seatback pad.

  2. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    1. A010HN1

      Attach the 2 hooks.

    2. A010GC3

      Attach the 2 claws to install the 2 headrest supports.

    3. A010GCD

      Install the front seat headrest.

    4. A010GJFE01

      Install the wire in the order shown in the illustration.

    5. A010HE4

      Attach the 2 claws to attach the wire.

    6. A010G4P

      Attach the 2 claws to install the active headrest lower unit.

    7. A010IKT

      Pull the wire and connect the end of the wire to the active headrest lower unit.

    8. A010HQA

      Install a new cable tie.

    9. A010L81

      Attach the 2 hooks and close the seatback mat.

    10. A010JS3E02
      Text in Illustration
      *1 Hook
      *2 Hog Ring
      *3 Hog Ring Pliers

      Attach the 3 hooks.

    11. Using hog ring pliers, install the upper part of the seatback cover to the seatback pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    12. A010IWX

      Attach the seatback cover bracket with the screw.

    13. A010L5V

      Pass the 2 straps through the separate type front seatback pad holes to the backside.

    14. A010KD8

      Attach the 2 hooks to install the 2 straps.

    15. A010JHK

      Attach the 2 hooks at the bottom of the seatback cover

    16. Attach the 4 hooks to install the cover.

      A010LK7

  3. INSTALL FRONT SEAT INNER CUSHION SHIELD LH


    1. A010FYQE01
      Text in Illustration
      *1 Hook
      *2 Wire Harness Clamp

      Attach the wire harness clamp.

    2. Attach the hook to install the cushion shield.

    3. Install the 2 screws.

  4. INSTALL FRONT SEAT CUSHION SHIELD LH WITH FRONT SEAT INNER NO. 1 CUSHION SHIELD


    1. A010H4B

      for Driver Side:

      Connect the connector.

    2. A010L01

      Attach the hook to install the front seat cushion shield LH with front seat inner No. 1 cushion shield.

    3. Install the 2 screws.

    4. A010KW3

      Attach the 2 claws and install the 2 screws.

  5. INSTALL SLIDE & VERTICAL POWER SEAT SWITCH KNOB


    1. A010LMY

      Attach the 4 claws to install the knob.

  6. INSTALL RECLINING POWER SEAT SWITCH KNOB


    1. A010M69

      Attach the 2 claws to install the knob.

  7. INSTALL FRONT SEAT ASSEMBLY


    1. Install the front seat assembly Click here.

  8. CHECK SRS WARNING LIGHT


    1. Check the SRS warning light Click here.

  9. INSPECT FRONT SEAT ASSEMBLY


    1. Check the front seat assembly Click here.

    2. Check the seat heater operation.


      1. Turn the ignition switch to ON.

      2. Operate the seat heater switch ON.

      3. Wait 5 minutes or more and confirm that the seat surface becomes warm.