FRONT POWER SEAT MOTOR ASSEMBLY (for Reclining) REMOVAL

Note

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. REMOVE FRONT SEAT ASSEMBLY


    1. Remove the front seat assembly Click here.

  2. REMOVE RECLINING POWER SEAT SWITCH KNOB


    1. A010IBFE01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape around the cushion shield.

    2. Using a screwdriver, detach the 2 claws and remove the knob.

      Tech Tips

      Tape the screwdriver tip before use.

  3. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. A010K86E01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 4 claws and remove the knob.

      Tech Tips

      Tape the screwdriver tip before use.

  4. REMOVE FRONT SEAT CUSHION SHIELD LH WITH FRONT SEAT NO. 1 INNER CUSHION SHIELD LH


    1. A010GPB

      Remove the 2 screws and detach the 2 claws.

    2. A010HQT

      Remove the 2 screws.

    3. Pull the shield to detach the hook and remove the front seat cushion shield LH with front seat inner No. 1 cushion shield.

    4. A010H4B

      for Driver Side:

      Disconnect the connector.

  5. REMOVE FRONT SEAT INNER CUSHION SHIELD LH


    1. A010J3IE01
      Text in Illustration
      *1 Hook
      *2 Wire Harness Clamp

      Remove the 2 screws.

    2. Pull the shield to detach the hook and remove the shield.

    3. Detach the wire harness clamp.

  6. REMOVE SEPARATE TYPE FRONT SEATBACK COVER


    1. Detach the 4 hooks.

      A010GI3
    2. A010JHK

      Detach the 2 hooks from the bottom of the seatback cover and roll up the seatback cover.

    3. A010KG1

      Detach the 2 hooks and disconnect the 2 straps.

    4. A010LR4

      Pass the 2 straps through the separate type front seatback pad holes to the surface.

    5. Roll up the cover.

    6. A010IWX

      Remove the screw and detach the seatback cover bracket.

    7. A010G5EE01
      Text in Illustration
      *1 Hook
      *2 Hog Ring

      Remove the hog rings and detach the 3 hooks from the center of the seatback pad and roll up the seatback cover.

    8. A010LXH

      Detach the 2 hooks and open the seatback mat.

    9. A010HQA

      Cut off the cable tie.

    10. A010HPR

      Pull the wire to loosen it, and then disconnect the end of the wire from the active headrest lower unit.

    11. A010LF4

      Detach the 2 claws and remove the active headrest lower unit.

    12. A010HE4

      Using a screwdriver, detach the 2 claws and wire.

      Tech Tips

      Tape the screwdriver tip before use.

    13. A010HNJE01

      Disconnect the wire in the order shown in the illustration.

    14. A010M4CE01

      Push the headrest support and detach the claw.

    15. Using a screwdriver, detach the claw and remove the front seat headrest.

      Tech Tips

      Tape the screwdriver tip before use.

      Text in Illustration
      *1 Protective Tape
    16. A010J3Q

      Detach the 2 claws and remove the 2 headrest supports.

    17. A010HN1

      Detach the 2 hooks and remove the seatback cover.

  7. REMOVE POWER SEAT MOTOR ASSEMBLY (for Reclining)


    1. A00DUA6

      Remove the seatback pad.

    2. A00DTO3

      for Driver Side:

      Disconnect the connectors.

    3. A00DUSX

      for Passenger Side:

      Disconnect the connector.

    4. A00DUH3

      Detach the 8 hooks and remove the seatback spring.

    5. A00DQC6

      Push in the inner reclining rod.

    6. A00DUUX

      Push in the inner reclining rod and remove the reclining rod assembly.

    7. A00DT86

      Remove the bolt and motor.