FRONT SEAT ASSEMBLY (for Manual Seat) REASSEMBLY

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. INSTALL NO. 2 REAR UPPER SEAT TRACK COVER


    1. A00OJSN

      Attach the 3 claws to install the No. 2 rear upper seat track cover.

  2. INSTALL REAR UPPER SEAT TRACK COVER


    1. A00OIJD

      Attach the 3 claws to install the rear upper seat track cover.

  3. INSTALL SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY

    A00OLIN

    1. Attach the 8 hooks to install the separate type front seat cushion spring assembly to the front seat adjuster assembly LH.

  4. INSTALL FRONT SEAT ADJUSTER ASSEMBLY LH


    1. A00OKH3

      Using a T50 "TORX" socket wrench, install the front seat adjuster assembly LH with the 4 "TORX" bolts.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }

  5. INSTALL FRONT SEAT INNER BELT ANCHOR BRACKET COVER LH

    A00OKET

    1. Install the front seat inner belt anchor bracket cover LH with the screw.

  6. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH

    A00OI3G

    1. Install the front seat lower cushion shield LH with the screw.

  7. INSTALL FRONT SEAT WIRE LH (w/ Lumbar Support)


    1. A00OIEI

      Attach the claw to install the front seat wire LH.

    2. Attach the 3 wire harness clamps.

    3. A00OLKU

      Attach the wire harness clamp.

  8. INSTALL SEAT CLIMATE CONTROL CONTROLLER LH (w/ Seat Heater System)


    1. A00OJUV

      Attach the claw to install the seat climate control controller LH.

    2. Connect the connector.

  9. INSTALL FRONT SEAT AIRBAG ASSEMBLY LH


    1. Install front seat airbag assembly LH with 2 new nuts.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

    2. Attach the 4 harness clamps and connect the connector clamp.

  10. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/ Lumbar Support)

    A00OJ4JE01

    1. Attach the 2 hooks B to install the lumbar support adjuster assembly LH to the seatback spring.

      Text in Illustration
      *1 Back Sheet
      *2 Hook A
      *3 Hook B
      *4 Cable Tie

    2. Install 2 new cable ties.

    3. Return the 2 back sheets to their original positions and attach the 4 hooks A.

    4. A00OM9P

      Return the wire harness to its original position as shown in the illustration.

    5. A00OLVO

      Attach the 8 hooks to install the seatback spring.

    6. A00ON1B

      Connect the connector.

  11. INSTALL FRONT SEATBACK HEATER ASSEMBLY

    Note

    When replacing either the front seatback heater assembly or separate type front seatback pad due to a malfunction, be sure to replace both of them with new parts.


    1. Remove the peeling paper from a new front seatback heater assembly.

    2. A00OHYV

      Install the front seatback heater assembly to a new separate type front seatback pad.

  12. INSTALL SEPARATE TYPE FRONT SEATBACK PAD

    A00OJ83

    1. Install the separate type front seatback pad.

  13. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    1. A00ONM4

      Attach the 2 hooks.

    2. A00OMKO

      Attach the 2 claws to install the 2 front seat headrest supports.

    3. w/ Active Headrest:


      1. A00OJU0

        Install the front seat headrest assembly.

        Note

        Push in the front seat headrest assembly until the headrest lock engages.

      2. A00ONJ0

        Pass the cable through the hole of the seatback frame.

      3. A00OJDI

        Attach the 2 claws to install the clip.

      4. A00OIX4E01
        Text in Illustration
        *1 Cable End

        Pull the cable through the clip until the cable end reaches the clip.

      5. A00OI4E

        Install a new cable tie.

      6. A00OKGKE01
        Text in Illustration
        *1 Hook
        *2 Hog Ring
        *3 Hog Ring Pliers

        Attach the 2 hooks to close the seatback mat.

      7. Using hog ring pliers, install a new hog ring.

      8. A00OLW6

        Attach the 2 claws to connect the cable to the active headrest lower unit.

      9. A00OJ98

        Attach the 2 claws to install the active headrest lower unit.

      10. A00OMWJE01
        Text in Illustration
        *1 Cable End
        A00OJPS Pull

        Pull the cable and connect the cable end to the active headrest lower unit.

      11. A00OIBR

        Attach the 7 hooks to install the actuator shield.

    4. A00OL1YE02
      Text in Illustration
      *1 Hook
      *2 Hog Ring
      *3 Hog Ring Pliers

      Attach the 3 hooks.

    5. Using hog ring pliers, install the upper part of the separate type front seatback cover to the separate type front seatback pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    6. A00OIU0E01
      Text in Illustration
      *1 Seatback Cover Bracket

      Attach the seatback cover bracket with the screw.

      Note

      After the separate type front seatback cover is installed, make sure the seatback cover bracket is not twisted.

    7. A00OIFV

      Pass the 2 straps through the 2 holes of the separate type front seatback pad to the backside.

    8. A00OMX4

      Attach the 2 hooks to connect the 2 straps.

    9. A00OILD

      Attach the 2 hooks at the bottom of the separate type front seatback cover.

    10. Attach the 2 hooks.

      A00OM3Y
    11. A00ON1Q

      w/o Active Headrest:

      Install the front seat headrest assembly.

      Note

      Push in the front seat headrest assembly until the headrest lock engages.

  14. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY

    Tech Tips

    Perform this procedure when it is necessary to remove and reinstall or replace the separate type front seatback assembly.


    1. A00OLG0

      Using a T50 "TORX" socket wrench, install the separate type front seatback assembly to the front seat adjuster assembly LH with the 4 "TORX" bolts.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }

    2. Attach the 2 wire harness clamps.

    3. A00OL64

      Attach the connector.

    4. w/ Active Headrest:


      1. A00OJU0

        Install the front seat headrest assembly.

        Note

        Push in the front seat headrest assembly until the headrest lock engages.

      2. A00ONJ0

        Pass the cable through the hole of the seatback frame.

      3. A00OJDI

        Attach the 2 claws to install the clip.

      4. A00OIX4E01
        Text in Illustration
        *1 Cable End

        Pull the cable through the clip until the cable end reaches the clip.

      5. A00OI4E

        Install a new cable tie.

      6. A00OKGKE01
        Text in Illustration
        *1 Hook
        *2 Hog Ring
        *3 Hog Ring Pliers

        Attach the 2 hooks to close the seatback mat.

      7. Using hog ring pliers, install a new hog ring.

      8. A00OLW6

        Attach the 2 claws to connect the cable to the active headrest lower unit.

      9. A00OJ98

        Attach the 2 claws to install the active headrest lower unit.

      10. A00OMWJE01
        Text in Illustration
        *1 Cable End
        A00OJPS Pull

        Pull the cable and connect the cable end to the active headrest lower unit.

      11. A00OIBR

        Attach the 7 hooks to install the actuator shield.

      12. A00OL1YE02
        Text in Illustration
        *1 Hook
        *2 Hog Ring
        *3 Hog Ring Pliers

        Attach the 3 hooks.

      13. Using hog ring pliers, install the upper part of the separate type front seatback cover to the separate type front seatback pad with new hog rings.

        Note


        • Be careful not to damage the cover.

        • When installing the hog rings, avoid wrinkling the cover.

      14. A00OIU0E01
        Text in Illustration
        *1 Seatback Cover Bracket

        Attach the seatback cover bracket with the screw.

        Note

        After the separate type front seatback cover is installed, make sure the seatback cover bracket is not twisted.

    5. w/ Lumbar Support:


      1. A00ON3R

        Connect the connector.

      2. A00OLKU

        Attach the wire harness clamp.

      3. A00OIFV

        Pass the 2 straps through the 2 holes of the separate type front seatback pad to the backside.

      4. A00OMX4

        Attach the 2 hooks to connect the 2 straps.

      5. A00OILD

        Attach the 2 hooks at the bottom of the separate type front seatback cover.

    6. Attach the 2 hooks.

      A00OM3Y
    7. A00ON1Q

      w/o Active Headrest:

      Install the front seat headrest assembly.

      Note

      Push in the front seat headrest assembly until the headrest lock engages.

  15. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)

    Note

    When replacing either the front seat cushion heater assembly or separate type front seat cushion pad due to a malfunction, be sure to replace both of them with new parts.


    1. Remove the peeling paper from a new front seat cushion heater assembly LH.

    2. A00OLW4

      Install the front seat cushion heater assembly LH to a new separate type front seat cushion pad.

  16. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. A00OKGP

      Attach the hooks to install the separate type front seat cushion cover to the separate type front seat cushion pad.

      Note


      • Be careful not to damage the cover.

      • When attaching the hooks, avoid wrinkling the cover.

  17. INSTALL SEAT CUSHION COVER WITH PAD


    1. Attach the hooks to install the seat cushion cover with pad.

      A00ONV2E01
      Text in Illustration
      *A w/ Seat Heater System - -

    2. w/ Seat Heater System:

      Connect the connector.

    3. A00OKBS

      w/ Lumbar Support:

      Attach the wire harness clamp.

    4. A00OLIT

      for Front Passenger Side:

      Attach the 2 hooks to connect the connector holder.

    5. w/ Seat Heater System:


      1. A00OI5P

        Connect the connector.

      2. A00OLYG

        Install a new cable tie.

    6. for Driver Side:


      1. A00OKYZ

        Attach the 2 claws to install the vertical adjuster handle bracket with connector link.

      2. A00OKQFE01
        Text in Illustration
        *1 Connector Link

        Connect the connector link and install the clip.

    7. A00OHRA

      Using a 15 mm socket wrench, install the reclining handle with the nut.

      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }
    8. A00OIV1

      Install the spring.

  18. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH


    1. A005REIE01
      Text in Illustration
      *1 Protruding Part

      Install the front seat inner belt with the nut.

      Torque:
      41 N*m  { 418 kgf*cm, 30 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

    2. for Driver Side:

      Connect the connector and attach the clamps.

    3. for Passenger Side:

      Connect the connectors and attach the clamps.

  19. INSTALL FRONT SEAT INNER CUSHION SHIELD LH


    1. A00ON87E01
      Text in Illustration
      *1 Hook
      *2 Wire Harness Clamp

      Attach the wire harness clamp and hook to install the front seat inner cushion shield LH.

    2. Install the 2 screws.

  20. INSTALL LUMBAR FRONT POWER SEAT SWITCH (w/ Lumbar Support)


    1. A00OL4J

      Install the lumbar front power seat switch with the 2 screws.

  21. INSTALL FRONT SEAT CUSHION SHIELD LH


    1. A00OIA6

      w/ Lumbar Support:

      Connect the connector.

    2. A00OJGH

      Attach the claw and hook to install the front seat cushion shield LH.

    3. Install the 2 screws.

    4. A00OJNF

      Attach the 2 rubber bands.

  22. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH


    1. A00OMSX

      Attach the claw to install the reclining adjuster release handle LH.

  23. INSTALL VERTICAL ADJUSTING HANDLE LH (for Driver Side)


    1. A00OMVH

      Install the vertical adjusting handle LH with the 2 screws.

  24. INSTALL VERTICAL SEAT ADJUSTER KNOB CAP (for Driver Side)


    1. A00OM9G

      Attach the 3 claws to install the vertical seat adjuster knob cap.