METER / GAUGE SYSTEM, Diagnostic DTC:B1500

DTC Code DTC Name
B1500 Fuel Sender Open Detected

DESCRIPTION

This DTC is stored when the combination meter detects a fuel sender gauge malfunction.

DTC Code DTC Detection Condition Trouble Area
B1500 The combination meter detects a fuel sender gauge malfunction.

  • Harness or connector

  • Combination meter assembly

  • Fuel suction with pump assembly

  • Fuel sender gauge assembly

WIRING DIAGRAM

A00OJM3E01

INSPECTION PROCEDURE

PROCEDURE


  1. READ VALUE USING INTELLIGENT TESTER (FUEL SENDER GAUGE)


    1. Use the Data List to check if the fuel receiver gauge is operating properly Click here.

      Combination Meter
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Fuel Input Fuel sender gauge (main) input signal/Min.: 0, Max.: 127.5 Fuel sender input value Unit: L
      OK
      Fuel amount value displayed on the intelligent tester is almost the same as needle indication.

    NG

    REPLACE COMBINATION METER ASSEMBLY Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (COMBINATION METER - FUEL SUCTION WITH PUMP AND BODY GROUND)

    A00OKG6E01
    Text in Illustration
    *1

    Front view of wire harness connector

    (to Combination Meter Assembly)
    *2

    Front view of wire harness connector

    (to Fuel Suction with Pump and Gauge Assembly)

    1. Disconnect the D66 meter connector.

    2. Disconnect the G24 gauge connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D66-37 (L) - G24-2 (FS) Always Below 1 Ω
      D66-24 (E) - G24-3 (FE)
      D66-21 (ET) - Body ground
      D66-37 (L) or G24-2 (FS) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT FUEL SUCTION WITH PUMP ASSEMBLY

    A00ON19E01

    1. for 1ZR-FAE:

      Remove the fuel suction with pump assembly Click here.

    2. for 2ZR-FAE:

      Remove the fuel suction with pump assembly Click here.

    3. for 3ZR-FE:

      Remove the fuel suction with pump assembly Click here.

    4. for 3ZR-FAE:

      Remove the fuel suction with pump assembly Click here.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A-2 (FS) - B-2 (FS) Always Below 1 Ω
      A-3 (FE) - B-3 (FE)

      Tech Tips


      • for 1ZR-FAE:

        If it is necessary to replace the fuel suction with pump assembly, refer to the following procedures Click here.

      • for 2ZR-FAE:

        If it is necessary to replace the fuel suction with pump assembly, refer to the following procedures Click here.

      • for 3ZR-FE:

        If it is necessary to replace the fuel suction with pump assembly, refer to the following procedures Click here.

      • for 3ZR-FAE:

        If it is necessary to replace the fuel suction with pump assembly, refer to the following procedures Click here.


    NG

    REPLACE FUEL SUCTION WITH PUMP AND GAUGE ASSEMBLY

    OK

  4. INSPECT FUEL SENDER GAUGE ASSEMBLY

    A00OKAYE01
    Text in Illustration
    *1

    Component without harness connected

    (Fuel Sender Gauge Assembly)

    1. for 1ZR-FAE:

      Remove the fuel sender gauge Click here.

    2. for 2ZR-FAE:

      Remove the fuel sender gauge Click here.

    3. for 3ZR-FE:

      Remove the fuel sender gauge Click here.

    4. for 3ZR-FAE:

      Remove the fuel sender gauge Click here.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 (FS) - 3 (FE) Float level F (upper) 12 to 18 Ω
      Float level E (lower) 405 to 415 Ω

      Tech Tips


      • for 1ZR-FAE:

        If it is necessary to replace the fuel sender gauge assembly, refer to the following procedures Click here.

      • for 2ZR-FAE:

        If it is necessary to replace the fuel sender gauge assembly, refer to the following procedures Click here.

      • for 3ZR-FE:

        If it is necessary to replace the fuel sender gauge assembly, refer to the following procedures Click here.

      • for 3ZR-FAE:

        If it is necessary to replace the fuel sender gauge assembly, refer to the following procedures Click here.


    NG

    REPLACE FUEL SENDER GAUGE ASSEMBLY

    OK

    REPLACE COMBINATION METER ASSEMBLY Click here