NAVIGATION RECEIVER (for DVD) REMOVAL


  1. REMOVE ENGINE ROOM SIDE COVER


    1. A00DSOB

      Remove the clip and engine room side cover.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL


    1. A00DSVAE01
      Text in Illustration
      *1 Protective Tape
      *2 Clamp
      *3 Guide

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 2 clips and 5 claws.

    3. Detach the clamp.

    4. Detach the guide near the front of the vehicle and remove the finish panel.

  4. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. A00DQADE01
      Text in Illustration
      *1 Protective Tape
      *2 Clamp
      *3 Guide

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 2 clips and 5 claws.

    3. Detach the clamp.

    4. Detach the guide near the front of the vehicle and remove the finish panel.

  5. REMOVE NO. 3 BOX PANEL (w/o Console Box Lid)


    1. A005V31E02
      Text in Illustration
      *1 Protective Tape

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 6 clips and remove the box panel.

  6. REMOVE NO. 3 BOX PANEL (w/ Console Box Lid)


    1. Place protective tape as shown in the illustration.

    2. Using a moulding remover, detach the 6 clips and remove the box panel.

      A005V11E01
      Text in Illustration
      *1 Protective Tape

  7. REMOVE INSTRUMENT PANEL FINISH PANEL END LH


    1. Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

      A00DV3GE01

  8. REMOVE INSTRUMENT PANEL FINISH PANEL END RH (for LHD)


    1. A00DUWJ

      Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

  9. REMOVE INSTRUMENT PANEL FINISH PANEL END RH (for RHD)


    1. w/o TOYOTA Parking Assist-sensor System:


      1. Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

    2. w/ TOYOTA Parking Assist-sensor System:


      1. Using a moulding remover B, detach the 4 clips and 5 claws.

      2. Remove the panel end and then disconnect the connector.

        A00DPQSE01

  10. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY WITH FINISH PANEL (for Audio-less, DVD Navigation System)


    1. A00DPXGE01
      Text in Illustration
      *1 Protective Tape

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 2 clips and hook.

    3. A00DSR7

      Detach the 3 claws and 3 hooks.

    4. Detach the 6 clips.

    5. A00DT2Z

      Remove the panel register. Then disconnect the connector and detach the clamp.

  11. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET


    1. A003B5C

      Remove the 4 screws.

    2. A003EO8

      Pull the navigation receiver.

    3. Disconnect the connectors and remove the navigation receiver.

  12. REMOVE NO. 1 RADIO BRACKET


    1. A003BB1

      Remove the 3 screws and bracket.

  13. REMOVE NO. 2 RADIO BRACKET


    1. A003ANX

      Remove the 3 screws and bracket.