NAVIGATION SYSTEM (for HDD) Reverse Signal Circuit

DESCRIPTION

The navigation receiver assembly receives a reverse signal from the park/neutral position switch*1 or back-up light switch*2 and information about the navigation antenna, and then adjusts the vehicle position.

*1: for CVT

*2: for Manual Transaxle

WIRING DIAGRAM

A00DQ9TE01

INSPECTION PROCEDURE

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK NAVIGATION RECEIVER ASSEMBLY (DISPLAY CHECK MODE)


    1. A00DSPME02

      Enter the "Failure Check/Setting" mode and select "Vehicle Signal" Click here.

    2. Check that the display changes between ON and OFF according to the shift lever operation.

      OK
      Shift lever Position Display
      R ON
      Except R OFF

      Tech Tips

      This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever operation.


    NG

    CHECK NAVIGATION RECEIVER ASSEMBLY (REVERSE SIGNAL) Click here

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  2. CHECK NAVIGATION RECEIVER ASSEMBLY (REVERSE SIGNAL)

    A00DQL9E05
    Text in Illustration
    *1

    Component with harness connected

    (Navigation Receiver Assembly)

    1. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      D25-5 (REV) - Body ground

      Ignition switch ON

      Shift lever in R

      		 11 to 14 V
      D25-5 (REV) - Body ground

      Ignition switch ON

      Shift lever in any position except R

      		 Below 1 V

    NG

    CHECK TRANSAXLE TYPE Click here

    OK

    REPLACE NAVIGATION RECEIVER ASSEMBLY Click here

  3. CHECK TRANSAXLE TYPE


    1. Check the transaxle type.

      Result
      Result Proceed to
      CVT A
      Manual Transaxle B

    B

    CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - BACK-UP LIGHT SWITCH) Click here

    A

  4. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - PARK/NEUTRAL POSITION SWITCH)


    1. A00DQ6IE01

      Disconnect the D25 navigation receiver assembly connector.

    2. A00DRCLE01

      Disconnect the B14 park/neutral position switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D25-5 (REV) - B14-2 (RL) Always Below 1 Ω
      D25-5 (REV) - Body ground Always 10 kΩ or higher
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Navigation Receiver Assembly)
      *2

      Front view of wire harness connector

      (to Park/Neutral Position Switch)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. INSPECT PARK/NEUTRAL POSITION SWITCH


    1. A00DQ68E01
      Text in Illustration
      *1

      Component without harness connected

      (Park/Neutral Position Switch)

      Disconnect the B14 switch connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (RB) - 2 (RL) Shift lever in R Below 1 Ω
      1 (RB) - 2 (RL) Shift lever in P 10 kΩ or higher
      Result
      Result Proceed to
      OK A
      NG (for K111) B
      NG (for K311) C

    B

    REPLACE PARK/NEUTRAL POSITION SWITCH Click here

    C

    REPLACE PARK/NEUTRAL POSITION SWITCH Click here

    A

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  6. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - BACK-UP LIGHT SWITCH)


    1. A00DQ6IE01

      Disconnect the D25 navigation receiver assembly connector.

    2. A00DQNVE01

      Disconnect the B5 switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D25-5 (REV) - B5-1 (RL) Always Below 1 Ω
      D25-5 (REV) - Body ground Always 10 kΩ or higher
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Navigation Receiver Assembly)
      *2

      Front view of wire harness connector

      (to Back-up Light Switch)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. INSPECT BACK-UP LIGHT SWITCH ASSEMBLY


    1. A00DTZDE01
      Text in Illustration
      *1

      Component without harness connected

      (Back-up Light Switch)

      Disconnect the B5 switch connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (RL) - 2 (RB) Shift lever in R Below 1 Ω
      1 (RL) - 2 (RB) Shift lever not in R 10 kΩ or higher
      Result
      Result Proceed to
      OK A
      NG (for EB60) B
      NG (for EC60) C

    B

    REPLACE BACK-UP LIGHT SWITCH ASSEMBLY Click here

    C

    REPLACE BACK-UP LIGHT SWITCH ASSEMBLY Click here

    A

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here