STEREO JACK ADAPTER ASSEMBLY REMOVAL


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL


    1. A00OLPBE01
      Text in Illustration
      *1 Protective Tape
      *2 Clamp
      *3 Guide

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 2 clips and 5 claws.

    3. Detach the clamp.

    4. Detach the guide near the front of the vehicle and remove the finish panel.

  4. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. A00OK10E01
      Text in Illustration
      *1 Protective Tape
      *2 Clamp
      *3 Guide

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 2 clips and 5 claws.

    3. Detach the clamp.

    4. Detach the guide near the front of the vehicle and remove the finish panel.

  5. REMOVE NO. 3 BOX PANEL


    1. Place protective tape as shown in the illustration.

    2. Using a moulding remover, detach the 6 clips and remove the box panel.

      A010J65E01
      Text in Illustration
      *1 Protective Tape

  6. REMOVE INSTRUMENT PANEL FINISH PANEL END LH


    1. Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

      A00OME5E01

  7. REMOVE INSTRUMENT PANEL FINISH PANEL END RH (for LHD)


    1. A00OM2F

      Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

  8. REMOVE INSTRUMENT PANEL FINISH PANEL END RH (for RHD)


    1. w/o TOYOTA Parking Assist-sensor System:


      1. Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

    2. w/ TOYOTA Parking Assist-sensor System:


      1. Using a moulding remover B, detach the 4 clips and 5 claws.

      2. Remove the panel end and then disconnect the connector.

        A00OI5CE01

  9. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)


    1. A010M16

      Twist the shift lever knob in the direction indicated by the arrow and remove it.

  10. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle and CVT)


    1. A010HDR

      Twist the shift lever knob in the direction indicated by the arrow and remove it.

  11. REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY (for Manual Transaxle)


    1. A010KDA

      Detach the cover.

    2. A010KPR

      Using a moulding remover B, detach the 2 claws.

    3. Detach the 6 clips and remove the console panel.

  12. REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY (for Automatic Transaxle and CVT)


    1. A010HFF

      Using a moulding remover B, detach the 2 claws.

    2. Detach the 6 clips.

    3. Remove the console panel and then disconnect the connector.

  13. REMOVE BOX BOTTOM PANEL


    1. A010LWH

      Detach the 4 claws and remove the box bottom panel.

  14. REMOVE NO. 1 STEREO JACK ADAPTER ASSEMBLY


    1. A010GYH

      Detach the 2 claws and remove the stereo jack adapter.