STEREO JACK ADAPTER ASSEMBLY REMOVAL


  1. REMOVE ENGINE ROOM SIDE COVER


    1. A00DSOB

      Remove the clip and engine room side cover.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note


    • w/ Navigation System (for HDD):

      After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL


    1. A00DSVAE01
      Text in Illustration
      *1 Protective Tape
      *2 Clamp
      *3 Guide

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 2 clips and 5 claws.

    3. Detach the clamp.

    4. Detach the guide near the front of the vehicle and remove the finish panel.

  4. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. A00DQADE01
      Text in Illustration
      *1 Protective Tape
      *2 Clamp
      *3 Guide

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 2 clips and 5 claws.

    3. Detach the clamp.

    4. Detach the guide near the front of the vehicle and remove the finish panel.

  5. REMOVE NO. 3 BOX PANEL (w/ Console Box Lid)


    1. Place protective tape as shown in the illustration.

    2. Using a moulding remover, detach the 6 clips and remove the box panel.

      A005V11E01
      Text in Illustration
      *1 Protective Tape

  6. REMOVE NO. 3 BOX PANEL (w/o Console Box Lid)


    1. A005V31E02
      Text in Illustration
      *1 Protective Tape

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 6 clips and remove the box panel.

  7. REMOVE INSTRUMENT PANEL FINISH PANEL END LH


    1. Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

      A00DV3GE01

  8. REMOVE INSTRUMENT PANEL FINISH PANEL END RH (for LHD)


    1. A00DUWJ

      Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

  9. REMOVE INSTRUMENT PANEL FINISH PANEL END RH (for RHD)


    1. w/o TOYOTA Parking Assist-sensor System:


      1. Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

    2. w/ TOYOTA Parking Assist-sensor System:


      1. Using a moulding remover B, detach the 4 clips and 5 claws.

      2. Remove the panel end and then disconnect the connector.

        A00DPQSE01

  10. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)


    1. A005TOC

      Twist the shift lever knob in the direction indicated by the arrow and remove it.

  11. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle and CVT)


    1. A005R5W

      Twist the shift lever knob in the direction indicated by the arrow and remove it.

  12. REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY (for Manual Transaxle)


    1. A005VX2

      Detach the cover.

    2. A005V73

      Using a moulding remover B, detach the 2 claws.

    3. Detach the 6 clips and remove the console panel.

  13. REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY (for Automatic Transaxle and CVT)


    1. A005R3Y

      Using a moulding remover B, detach the 2 claws.

    2. Detach the 6 clips.

    3. Remove the console panel and then disconnect the connector.

  14. REMOVE BOX BOTTOM PANEL


    1. Detach the 4 claws and remove the panel.

      A003ELLE01

  15. REMOVE NO. 1 STEREO JACK ADAPTER ASSEMBLY


    1. A005R7G

      Detach the 2 claws and remove the stereo jack adapter.