REAR BRAKE REMOVAL

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The following procedure is for the LH side.


  1. REMOVE REAR WHEEL

  2. ENTER PARKING BRAKE FULL RELEASE MODE (ACTIVE TEST)


    1. Turn the ignition switch off.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the intelligent tester on.

    5. Enter the following menus: Chassis / Electric Parking Brake / Active Test / Full Release Mode Activation.

      Note

      If the parking brake cannot be released, use the luggage compartment's parking brake release tool to manually release the parking brake.

      Observe the following notices to release the parking brake with the emergency release cable.


      • Prevent the vehicle from moving with wheel chocks or equivalent.

      • Make sure the PARK warning light is off.

      • Make sure the shift lever is in P (for Automatic Transaxle), or 1st or R (for Manual Transaxle).

      • Make sure the ignition switch is off.

      • Perform all work on a level surface.

      • If using the parking brake release tool, be sure to turn the tool until it stops.

  3. DRAIN BRAKE FLUID

    Note

    Wash off brake fluid immediately if it comes in contact with any painted surface.

  4. REMOVE PARKING BRAKE LEVER PROTECTOR

  5. DISCONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY


    1. A00OMLG

      Remove the bolt and detach the clamp from the trailing arm.

    2. A00ONKZ

      Remove the clip and pin from the rear disc brake cylinder assembly. Then disconnect the end of the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.

    3. A00OIP1E02
      Text in Illustration
      *1 Claw

      Detach the claws of the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly. Then disconnect the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.

  6. DISCONNECT REAR BRAKE FLEXIBLE HOSE


    1. A00OKP0

      Remove the union bolt and gasket, and disconnect the rear brake flexible hose from the rear disc brake cylinder assembly.

  7. REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY


    1. A00OMPI

      Hold the rear disc brake slide pin and remove the 2 bolts and rear disc brake cylinder assembly.

  8. REMOVE REAR DISC BRAKE PAD


    1. A00OJH4

      Remove the 2 disc brake pads from the rear disc brake cylinder mounting.

  9. REMOVE REAR DISC BRAKE PAD SUPPORT PLATE


    1. A00ONZX

      Remove the rear disc brake pad support plates from the disc brake cylinder mounting.

      Note

      Each rear disc brake pad support plate has a different shape. Be sure to put an identification mark on each rear disc brake pad support plate so that it can be installed to its original position.

  10. REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN


    1. A00OMVL

      Remove the 2 rear disc brake cylinder slide pins from the disc brake cylinder mounting.

  11. REMOVE REAR DISC BRAKE CYLINDER SLIDE BUSH


    1. A00OI7T

      Using a screwdriver, remove the rear disc brake cylinder slide bush from the rear disc brake cylinder slide pin.

      Tech Tips

      Tape the screwdriver tip before use.

      Note

      Do not damage the rear disc brake cylinder slide pin.

  12. REMOVE REAR DISC BRAKE BUSH DUST BOOT


    1. A00ON2X

      Remove the 2 rear disc brake bush dust boots from the rear disc brake cylinder mounting.

  13. REMOVE REAR DISC BRAKE CYLINDER MOUNTING


    1. A00OHS2

      Remove the 2 bolts and rear disc brake cylinder mounting from the axle carrier.

  14. REMOVE REAR DISC


    1. A00ONLDE01
      Text in Illustration
      *1 Matchmark

      Place matchmarks on the disc and axle hub.

    2. Remove the rear disc.