ANTI-LOCK BRAKE SYSTEM TEST MODE PROCEDURE


  1. WARNING LIGHT INITIAL CHECK


    1. A005W8KE05

      Release the parking brake.

      CAUTION:

      When releasing the parking brake, set chocks to hold the vehicle for safety.

    2. When the ignition switch is ON, check that the ABS warning light and brake system warning light (red indicator) illuminate and then turn off after 3 seconds. If a light remains on, proceed to troubleshooting for the light circuit below.

      Trouble Area See procedure
      ABS warning light circuit (Remains on)

      Click here

      ABS warning light circuit (Does not come on)

      Click here

      Brake system warning light (red indicator) circuit (Remains on)

      Click here

      Brake system warning light (red indicator) circuit (Does not come on)

      Click here

  2. SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (Using the Intelligent Tester)

    Tech Tips

    If the ignition switch is turned from ON to ACC or off during Test Mode (signal check), DTCs stored during the sensor check will be cleared.


    1. Procedure to enter Test Mode.


      1. Turn the ignition switch off.

      2. Check that the steering wheel is in the straight-ahead position.

      3. Check that the shift lever is in P (for automatic transaxle model) or the parking brake is applied (for manual transaxle model).

      4. Connect the intelligent tester to the DLC3.

      5. Turn the ignition switch to ON.

      6. Turn the intelligent tester on.

      7. Switch the skid control ECU to Test Mode using the intelligent tester. Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check.

      8. A005WLEE83

        Check that the ABS warning light comes on for several seconds and then blinks in the Test Mode blinking pattern.

        If the ABS warning light does not blink, inspect the TS and CG terminal circuit and ABS warning light circuit.

        Trouble Area See procedure
        TS and CG terminal circuit

        Click here

        ABS warning light circuit (Remains on)

        Click here

        ABS warning light circuit (Does not come on)

        Click here

  3. SPEED SENSOR CHECK (Using the Intelligent Tester)


    1. Drive the vehicle straight-ahead.

      Accelerate the vehicle to a speed of 45 km/h (28 mph) or more over several seconds and check that the ABS warning light goes off.

      A005TK1E03

    2. Stop the vehicle.

      Note


      • The speed sensor check may not be completed if the speed sensor check is started while turning the steering wheel or spinning the wheels.

      • If the sensor check has not been completed, the ABS warning light will blink while driving and the ABS will not operate.

      Tech Tips

      When the sensor check has been completed, the ABS warning light goes off while driving and blinks in the Test Mode pattern while stationary.

  4. END OF SENSOR CHECK (Using the Intelligent Tester)


    1. A005WLEE83

      If the sensor check is completed, the ABS warning light blinks (Test Mode) when the vehicle stops and is off while the vehicle is being driven.

      Note

      If the sensor check is not completed, the ABS warning light blinks even while the vehicle is being driven and the ABS does not operate.

  5. READ DTC OF SENSOR CHECK FUNCTION (Using the Intelligent Tester)


    1. Read the DTC(s) by following the intelligent tester screen.

      Note


      • If only DTCs are displayed, repair the malfunctions and clear the DTCs.

      • If DTCs and Test Mode codes (DTCs of the sensor check function) are displayed, repair the malfunctions, clear the DTCs and perform the Test Mode inspection.

      Tech Tips

      Refer to the list of DTCs Click here.

  6. SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (Using SST Check Wire)

    Tech Tips

    If the ignition switch is turned from ON to ACC or off during Test Mode (signal check), DTCs stored during the sensor check will be cleared.


    1. Procedure to enter Test Mode.


      1. Turn the ignition switch off.

      2. Check that the steering wheel is in the straight-ahead position.

      3. Check that the shift lever is in P (for automatic transaxle model) or the parking brake is applied (for manual transaxle model).

      4. A005W38E24
        Text in Illustration
        *1 Front view of DLC3

        Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.

        SST
        09843-18040

      5. Turn the ignition switch to ON.

      6. A005WLEE83

        Check that the ABS warning light comes on for several seconds and then blinks in the Test Mode blinking pattern.

        If the ABS warning light does not blink, inspect the TS and CG terminal circuit, and ABS warning light circuit.

        Trouble Area See procedure
        TS and CG terminal circuit

        Click here

        ABS warning light circuit (Remains on)

        Click here

        ABS warning light circuit (Does not come on)

        Click here

  7. SPEED SENSOR CHECK (Using SST Check Wire)


    1. Drive the vehicle straight-ahead.

      Accelerate the vehicle to a speed of 45 km/h (28 mph) or more over several seconds and check that the ABS warning light goes off.

      A005TK1E03

    2. Stop the vehicle.

      Note


      • The speed sensor check may not be completed if the speed sensor check is started while turning the steering wheel or spinning the wheels.

      • If the sensor check has not been completed, the ABS warning light will blink while driving and the ABS system will not operate.

      Tech Tips

      When the sensor check has been completed, the ABS warning light goes off while driving and blinks in the Test Mode pattern while stationary.

  8. END OF SENSOR CHECK (Using SST Check Wire)


    1. A005WLEE83

      If the sensor check is completed, the ABS warning light blinks (Test Mode) when the vehicle stops and is off while the vehicle is driving.

      Note

      If the sensor check is not completed, the ABS warning light blinks even while the vehicle is driving and the ABS does not operate.

  9. READ DTC OF SENSOR CHECK FUNCTION (Using SST Check Wire)


    1. A005W38E25
      Text in Illustration
      *1 Front view of DLC3

      Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040

    2. Count the number of blinks of the ABS warning light.

      A005SSRE10

      Note


      • If only DTCs are displayed, repair the malfunctions and clear the DTCs.

      • If DTCs and Test Mode codes (DTCs of sensor check function) are displayed, repair the malfunctions, clear the DTCs and perform the Test Mode inspection.

      Tech Tips


      • If more than 1 malfunction is detected at the same time, the lowest numbered code will be displayed first.

      • Refer to the list of DTCs Click here.

    3. After performing the check, disconnect SST from terminals 12 (TS) and 4 (CG), and 13 (TC) and 4 (CG) of the DLC3, and turn the ignition switch off.

    4. Turn the ignition switch to ON to cancel the Test Mode.

      Tech Tips


      • If the ignition switch is not turned to ON after SST is removed from the DLC3, the previous Test Mode will continue.

      • If the ignition switch is turned to ON with terminals TS and CG connected, the previous Test Mode will continue.

  10. DTC OF SENSOR CHECK FUNCTION

    ABS Sensor
    DTC Code Detection Item Trouble Area
    C1271/71 Low output signal of front speed sensor RH

    • Front speed sensor RH

    • Sensor installation

    • Speed sensor rotor (Front axle hub sub-assembly RH)
    C1272/72 Low output signal of front speed sensor LH

    • Front speed sensor LH

    • Sensor installation

    • Speed sensor rotor (Front axle hub sub-assembly LH)
    C1273/73 Low output signal of rear speed sensor RH

    • Rear speed sensor RH (Rear axle hub and bearing assembly RH)

    • Sensor installation

    • Speed sensor rotor (Rear axle hub and bearing assembly RH)
    C1274/74 Low output signal of rear speed sensor LH

    • Rear speed sensor LH (Rear axle hub and bearing assembly LH)

    • Sensor installation

    • Speed sensor rotor (Rear axle hub and bearing assembly LH)
    C1275/75 Abnormal change in output signal of front speed sensor RH Speed sensor rotor (Front axle hub sub-assembly RH)
    C1276/76 Abnormal change in output signal of front speed sensor LH Speed sensor rotor (Front axle hub sub-assembly LH)
    C1277/77 Abnormal change in output signal of rear speed sensor RH Speed sensor rotor (Rear axle hub and bearing assembly RH)
    C1278/78 Abnormal change in output signal of rear speed sensor LH Speed sensor rotor (Rear axle hub and bearing assembly LH)

    Tech Tips

    The codes in this table are output only in Test Mode (signal check).