TIRE AND WHEEL SYSTEM INSPECTION


  1. INSPECT TIRE


    1. Check the tires for wear and proper inflation pressure.

      Cold Tire Inflation Pressure
      Tire Size Vehicle Speed Front Rear
      205/60R16 92V

      Driving below 160 km/h

      (100 mph)

      240 kPa (2.4 kgf/cm2, 35 psi)

      220 kPa (2.2 kgf/cm2, 32 psi)

      Driving over 160 km/h

      (100 mph)

      270 kPa (2.7 kgf/cm2, 40 psi)

      250 kPa (2.5 kgf/cm2, 37 psi)

      205/60R16 92V

      (for Algeria)

      		 -

      250 kPa (2.5 kgf/cm2, 37 psi)

      220 kPa (2.2 kgf/cm2, 32 psi)
      215/55R17 94W

      Driving below 160 km/h

      (100 mph)

      240 kPa (2.4 kgf/cm2, 35 psi)

      230 kPa (2.3 kgf/cm2, 34 psi)

      Driving over 160 km/h

      (100 mph)

      280 kPa (2.8 kgf/cm2, 41 psi)

      270 kPa (2.7 kgf/cm2, 40 psi)
      225/45R18 91W

      Driving below 160 km/h

      (100 mph)

      250 kPa (2.5 kgf/cm2, 37 psi)

      240 kPa (2.4 kgf/cm2, 35 psi)

      Driving over 160 km/h

      (100 mph)

      290 kPa (2.9 kgf/cm2, 43 psi)

      280 kPa (2.8 kgf/cm2, 41 psi)
      T145/70D17 106M -

      420 kPa (4.2 kgf/cm2, 60 psi)
    2. A00OHYX

      Using a dial indicator, check the runout of the tires.

      Tire runout
      1.0 mm (0.0394 in.) or less

  2. ROTATE TIRE


    1. A00OJM2E01
      Text in Illustration
      *a Front of the Vehicle
      *b Vehicle Wheels and Spare Tire Wheel are Same Type
      *c Vehicle Wheels and Spare Tire Wheel are Not Same Type, or There is No Spare Tire

      Rotate the tires as shown in the illustration.

  3. INSPECT WHEEL BALANCE


    1. A00OM58

      for Steel Wheel Type:

      Check and adjust the off-the-car balance.

      Standard Imbalance After Adjustment
      8.0 g (0.018 lb.) or less

      Tech Tips

      If necessary, check and adjust the on-the-car balance.

    2. A00OJZQE01

      for Aluminum Wheel Type:

      Check and adjust the off-the-car balance.

      Standard Imbalance After Adjustment
      8.0 g (0.018 lb.) or less

      Note


      • Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be attached.

      • Do not touch the adhesive surface of the tape.

      • Attach a sticking-type balance weight to the flat surface (A) shown in the illustration.

        Width (A)
        25 mm (0.984 in.)

      • Push the balance weight firmly so that it securely adheres to the position.

      • Do not reuse the balance weight.

      Tech Tips


      • The inner side balance weights should be installed by clipping them to the rim.

      • If necessary, check and adjust the on-the-car balance.

  4. INSPECT FRONT AXLE HUB BEARING


    1. Inspect the front axle hub bearing Click here.

  5. INSPECT REAR AXLE HUB BEARING


    1. Inspect the rear axle hub bearing Click here.