TRANSMISSION CONTROL CABLE REMOVAL


  1. REMOVE FRONT EXHAUST PIPE ASSEMBLY


    1. Remove the front exhaust pipe assembly Click here.

  2. REMOVE NO. 2 CYLINDER HEAD COVER


    1. A00OIJQ

      Hold the rear of the cover and raise it to detach the 2 clips on the rear of the cover. Continue to raise the cover to detach the 2 clips on the front of the cover and remove the cover.

      Note

      Attempting to detach both front and rear clips at the same time may cause the cover to break.

  3. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    1. A00OKGM

      Disconnect the mass air flow meter connector.

    2. Detach the wire harness from the 2 clamps.

    3. A00OMGP

      Disconnect the 2 clamps.

    4. A00OKSA

      Disconnect the ventilation hose.

    5. Loosen the band and remove the air cleaner cap.

  4. REMOVE AIR CLEANER CASE SUB-ASSEMBLY


    1. A00OI1G

      Detach the wire harness clamp from the air cleaner case.

    2. Remove the 3 bolts and air cleaner case.

  5. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL


    1. A00OLPBE01
      Text in Illustration
      *1 Protective Tape
      *2 Clamp
      *3 Guide

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 2 clips and 5 claws.

    3. Detach the clamp.

    4. Detach the guide near the front of the vehicle and remove the finish panel.

  6. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. A00OK10E01
      Text in Illustration
      *1 Protective Tape
      *2 Clamp
      *3 Guide

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 2 clips and 5 claws.

    3. Detach the clamp.

    4. Detach the guide near the front of the vehicle and remove the finish panel.

  7. REMOVE NO. 3 BOX PANEL (w/o Console Box Lid)


    1. A005V31E02
      Text in Illustration
      *1 Protective Tape

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 6 clips and remove the box panel.

  8. REMOVE NO. 3 BOX PANEL (w/ Console Box Lid)


    1. Place protective tape as shown in the illustration.

    2. Using a moulding remover, detach the 6 clips and remove the box panel.

      A005V11E01
      Text in Illustration
      *1 Protective Tape

  9. REMOVE INSTRUMENT PANEL FINISH PANEL END LH


    1. Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

      A00OME5E01

  10. REMOVE INSTRUMENT PANEL FINISH PANEL END RH (for LHD)


    1. A00OM2F

      Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

  11. REMOVE INSTRUMENT PANEL FINISH PANEL END RH (for RHD)


    1. w/o TOYOTA Parking Assist-sensor System:


      1. Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

    2. w/ TOYOTA Parking Assist-sensor System:


      1. Using a moulding remover B, detach the 4 clips and 5 claws.

      2. Remove the panel end and then disconnect the connector.

        A00OI5CE01

  12. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A005TOC

      Twist the shift lever knob in the direction indicated by the arrow and remove it.

  13. REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. A005VX2

      Detach the cover.

    2. A005V73

      Using a moulding remover B, detach the 2 claws.

    3. Detach the 6 clips and remove the console panel.

  14. REMOVE REAR CONSOLE BOX CUP HOLDER (w/ Console Box Lid)


    1. Remove the cup holder.

  15. REMOVE CONSOLE BOX CARPET (w/ Console Box Lid)


    1. Remove the 2 carpets.

  16. REMOVE CONSOLE BOX CARPET (w/o Console Box Lid)


    1. Remove the 3 carpets.

  17. REMOVE CONSOLE BOX ASSEMBLY (w/ Console Box Lid)


    1. for Manual Transaxle:

      Remove the 2 screws.

    2. for Automatic Transaxle and CVT:

      Remove the 4 screws.

    3. w/ Power Outlet Socket:

      Disconnect the connectors.

    4. Remove the 4 bolts and console box.

      A005S54E01

  18. REMOVE CONSOLE BOX ASSEMBLY (w/o Console Box Lid)


    1. w/ Power Outlet Socket:


      1. Disconnect the connectors.

    2. Remove the 2 screws.

    3. Remove the 4 bolts and console box.

      A005RJME01

  19. REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR

    A010JPR

    1. Remove the 3 nuts and front No. 1 floor heat insulator.

  20. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY


    1. A010HU3

      Remove the 2 clips and disconnect the 2 cables from the transaxle.

    2. A010G0E

      Remove the 2 clips and disconnect the 2 cables from the control cable bracket.

    3. A010KH9

      Remove the bolt and detach the bracket of the control cable assembly.

    4. A010M59

      Remove the 2 nuts and detach the grommet of the control cable assembly.

    5. A010LY1

      Remove the clip and disconnect the end of the select control cable.

    6. A010IDQ

      Remove the clip and disconnect the end of the shift control cable.

    7. A010M8Q

      Detach the claws and remove the control cable assembly.