TRANSMISSION CONTROL CABLE INSTALLATION


  1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY


    1. A010ISP

      Install the control cable assembly through the floor hole.

    2. Attach the 2 claws to connect the shift control cable and select control cable to the floor shift lever assembly.

    3. A010M59

      Attach the grommet of the control cable assembly with the 2 nuts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
    4. A010IDQ

      Connect the end of the shift control cable to the shift lever assembly and install the clip.

    5. A010KH9

      Attach the bracket of the control cable assembly with the bolt.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
    6. A010L03

      Connect the 2 cables to the control cable bracket with 2 new clips.

    7. A010H3U

      Connect the 2 cables to the transaxle and install the 2 clips.

    8. Release the lock of the cable length adjustment structure of the select cable.


      1. A010H13E01

        Twist the stopper.

      2. A010LA5E01

        Pull the lock piece outward from the case to release the lock.

    9. A010IUGE01
      Text in Illustration
      *1 Reverse Restrict Pin Assembly
      *2 Outer Lever

      Hook the outer lever of the manual transaxle onto the reverse restrict pin assembly to secure it.

    10. A010LY1

      Connect the end of the select control cable to the shift lever assembly and install the clip.

      Note


      • Make sure the lock piece of the select control cable is facing upward when the select control cable is connected.

      • Make sure the clip is inserted in the direction shown in the illustration.

    11. A010L50E01
      Text in Illustration
      *1 Slider
      *2 Inhibitor Wall

      Push the slider against the inhibitor wall.

      Note


      • Do not pull up the slider.

      • When adjusting the cable, make sure that the shift lever is not in 1 or 2.

    12. Lock the cable length adjustment structure of the select cable.


      1. A010H1FE01

        Push the lock piece into the case with the slider held against the inhibitor wall.

      2. A010LAVE01

        Return the stopper to prevent the lock from being released.

        Note


        • Push in the lock piece completely.

        • Make sure that the cable length adjustment structure is locked securely.

    13. A010HEAE01

      Move the shift lever to R to release the outer lever.

  2. INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR

    A010JPR

    1. Install the front No. 1 floor heat insulator with the 3 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  3. INSTALL CONSOLE BOX ASSEMBLY

    Click here

  4. INSTALL AIR CLEANER CASE SUB-ASSEMBLY


    1. A00OI1G

      Install the air cleaner case with the 3 bolts.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

    2. Attach the wire harness clamp to the air cleaner case.

  5. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


    1. A00OKSA

      Connect the air cleaner cap with the band.

    2. Connect the ventilation hose.

    3. A00OMGP

      Connect the 2 clamps.

    4. A00OKGM

      Attach the wire harness to the 2 clamps.

    5. Connect the mass air flow meter connector.

  6. INSTALL NO. 2 CYLINDER HEAD COVER


    1. A00OIJQ

      Attach the 4 clips to install the cover.

      Note


      • Be sure to attach the clips securely.

      • Do not apply excessive force or hit the cover to attach the clips. This may cause the cover to break.

  7. INSTALL FRONT EXHAUST PIPE ASSEMBLY

    Click here