PARK / NEUTRAL POSITION SWITCH INSTALLATION


  1. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

    A00OHZT

    1. Install the park/neutral position switch to the manual valve shaft.

    2. Temporarily install the 2 bolts.

    3. A00OKP7

      Install a new lock plate and the lock nut.

      Torque:
      6.9 N*m  { 70 kgf*cm, 61 in.*lbf }

    4. Temporarily install the control shaft lever.

    5. A00ONPXE01

      Turn the lever counterclockwise until it stops, and then turn it clockwise 2 notches.

    6. Remove the control shaft lever.

    7. A00ONPPE10
      Text in Illustration
      *1 Neutral Basic Line
      *2 Protrusion

      Align the groove with the neutral basic line.

    8. Hold the switch in this position and tighten the 2 bolts.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }
    9. A00OKEL

      Using a screwdriver, bend the tabs of the lock plate.

    10. A00OLA0

      Install the control shaft lever with the washer and nut.

      Torque:
      13 N*m  { 130 kgf*cm, 9 ft.*lbf }

  2. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

    A00OND7

    1. Connect the transmission control cable to the control shaft lever with the nut.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }
    2. A00OJCB

      Connect the park/neutral position switch connector.

  3. INSTALL BATTERY CARRIER

    A00OJKB

    1. Install the battery carrier with the 4 bolts.

      Torque:
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }

    2. Attach the 2 wire harness clamps.

  4. INSTALL BATTERY


    1. Install the battery tray.

    2. Install the battery.

    3. Install the battery clamp with the bolt and tighten the nut.

      Torque:
      for bolt
      17 N*m  { 168 kgf*cm, 12 ft.*lbf }
      for nut
      3.5 N*m  { 36 kgf*cm, 31 in.*lbf }

    4. Connect the cable to the positive (+) battery terminal.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

  5. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  6. INSTALL RADIATOR SUPPORT OPENING COVER


    1. A00OKW2

      Install the radiator support opening cover with the 7 clips.

  7. INSPECT SHIFT LEVER POSITION


    1. When moving the shift lever from P to R with the ignition switch ON and the brake pedal depressed, make sure that the shift lever moves smoothly and correctly into position.

    2. Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D and moves in reverse after moving the shift lever to R. If the operation cannot be performed as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.

  8. ADJUST SHIFT LEVER POSITION


    1. Remove the console box assembly Click here.

    2. Apply the parking brake and move the shift lever to N.

    3. A005V6LE01

      Disconnect the end of the transmission control cable assembly from the shift lever assembly.

    4. A005T1IE01
      Text in Illustration
      *1 Stopper
      *2 Nut

      Pull out the stopper of the transmission control cable.

      Note

      Do not remove the stopper. If the stopper is removed, reinstall it to its original position.

    5. Rotate the nut counterclockwise approximately 180° and, while holding the nut in that position, disconnect the transmission control cable from the shift lever retainer.

      Note

      Do not over-rotate the nut as it will come off the internal spring and the transmission control cable will not be reusable.

    6. A005VHLE01

      Push the 2 claws together at the top of the transmission control cable lock piece. While holding the 2 claws together, push the 2 lugs on the bottom of the lock piece toward each other and upward to pull out the lock piece.

    7. Turn the nut of the transmission control cable 180° counterclockwise. While holding the nut in place, push in the stopper until the stopper clicks twice.

      A005VB6E01
      Text in Illustration
      *1 Stopper *2 Nut

    8. Install the outer part of the transmission control cable to the shift lever retainer. Check that the spring is positioned at "A" and push in the stopper.

      A005SG3E01
      Text in Illustration
      *1 Stopper *3 Shift Lever Retainer
      *2 Nut *4 Spring

      Tech Tips

      If the stopper cannot be pushed in, slightly turn the nut clockwise and then push in the stopper again.

    9. A005VIFE01
      Text in Illustration
      *1 Lock Piece

      Connect the end of the cable to the shift lever assembly.

      Note


      • Make sure that the lock piece is pulled up.

      • Push on the end of the cable all the way to the base of the pin.

    10. A005VBXE01
      Text in Illustration
      *1 Lock Piece
      *2 Adjuster Case

      Push the lock piece into the adjuster case.

      Note

      Securely push in the lock piece until it locks.

    11. After adjusting the shift lever position, check the operation and function of the shift lever. If there is a problem, adjust the position again.

    12. Install the console box Click here.

  9. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    1. Apply the parking brake and turn the ignition switch to ON.

    2. Depress the brake pedal and check that the engine can be started when the shift lever is in N or P, but does not start when the shift lever is in other positions.

    3. Check that the back-up light illuminates and the reverse warning buzzer sounds when the shift lever is in R, but do not function when the shift lever is in other positions.

      If a malfunction or failure is found, check the park/ neutral position switch for continuity.