TRANSMISSION WIRE INSTALLATION


  1. INSTALL TRANSMISSION WIRE

    A00DUVUE02

    1. Coat a new O-ring with ATF WS and install it to the transmission wire connector.

    2. A00DTI2

      Install the transmission wire with the bolt.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

    3. Connect the transmission wire connector.

  2. CONNECT TRANSMISSION WIRE

    A00DRNRE08
    Text in Illustration
    *1 Lock Plate

    1. Coat the O-ring of the ATF temperature sensor with ATF WS.

    2. Install the ATF temperature sensor with the lock plate and bolt.

      Torque:
      6.6 N*m  { 67 kgf*cm, 58 in.*lbf }

    3. Connect the 5 shift solenoid valve connectors.

  3. INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

    A00DTXPE06

    1. Install the 2 magnets to the oil pan.

      Text in Illustration
      *1 Magnet
    2. A00DRR3E01

      Install a new gasket and the oil pan with the 18 bolts.

      Torque:
      7.8 N*m  { 80 kgf*cm, 69 in.*lbf }

  4. INSTALL NO. 1 ENGINE UNDER COVER (for 1AZ-FE)


    1. A005VAK

      Install the under cover with the 5 clips.

  5. INSTALL NO. 1 ENGINE UNDER COVER (for 3ZR-FE)


    1. A00ON3U

      Install the under cover with the 10 clips.

  6. INSTALL FRONT LOWER BUMPER ABSORBER

    A00DTLK

    1. Install the front lower bumper absorber with the 8 bolts and 3 screws.

    2. A00DUZW

      Install the 2 screws and 4 bolts.

  7. INSTALL BATTERY CARRIER

    A005RI3

    1. Install the battery carrier with the 4 bolts.

      Torque:
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }

    2. Attach the 2 wire harness clamps.

  8. INSTALL BATTERY


    1. Install the battery tray.

    2. Install the battery.

    3. Install the battery clamp with the bolt and tighten the nut.

      Torque:
      for bolt
      17 N*m  { 168 kgf*cm, 12 ft.*lbf }
      for nut
      3.5 N*m  { 36 kgf*cm, 31 in.*lbf }

    4. Connect the cable to the positive (+) battery terminal.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

  9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  10. ADD AUTOMATIC TRANSAXLE FLUID

    Fluid type
    Toyota Genuine ATF WS

  11. INSPECT TRANSAXLE FLUID LEVEL

    Tech Tips


    • Drive the vehicle so that the engine and transaxle are at the normal operating temperature.

      Fluid temperature
      70 to 80°C (158 to 176°F)

    • The ATF temperature can be checked with the intelligent tester.

      Enter the following menus: Powertrain / Engine and ECT / Data List / A/T Oil Temperature 1.


    1. A00DSUAE03

      Park the vehicle on a level surface and set the parking brake.

    2. With the engine idling and the brake pedal depressed, move the shift lever to each position from P to L, and then return it to P.

    3. Take out the ATF dipstick and wipe it clean.

    4. Fully push the dipstick back into the pipe.

    5. Take out the dipstick and check that the fluid level is at the HOT position.

  12. INSTALL RADIATOR SUPPORT OPENING COVER

    A005SU5

    1. Install the radiator support opening cover with the 8 clips.

  13. INSTALL ENGINE ROOM SIDE COVER

    A005RE1

    1. Install the engine room side cover with the clip.